Related Manuals for Allied Telesis AT-MC1005/2
Summary of Contents for Allied Telesis AT-MC1005/2
-
Page 1: Installation Guide
AT-MC1004 AT-MC1005/1 AT-MC1005/2 AT-MC1005/3 AT-MC1005/4 Gigabit Ethernet Media Converters Installation Guide PN 613-50438-00 Rev A... - Page 2 Copyright 2003 Allied Telesyn, Inc. 960 Stewart Drive, Suite B, Sunnyvale CA USA 94085 All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn, Inc. Ethernet is a registered trademark of Xerox Corporation. All other product names, company names, logos or other designations mentioned herein are trademarks or registered trademarks of their respective owners.
-
Page 3: Electrical Safety And Emission Compliance Statement
Gigabit Ethernet Media Converters Model Numbers: AT-MC1004, AT-MC1005/1, AT-MC1005/2, AT-MC1005/3, AT-MC1005/4 This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 4 Electrical Safety and Emission Compliance Statement Industry Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. RFI Emission EN55022 Class B Warning: In a domestic environment this product may cause radio...
-
Page 5: Table Of Contents
Table of Contents Electrical Safety and Emission Compliance Statement .......iii Table of Contents .................... v Preface ......................vii Where to Find Web-based Guides ..............vii Document Conventions ..................vii Contacting Allied Telesyn Technical Support..........viii Online Support ..................viii Telephone Support ................... viii E-mail Support ..................viii Returning Products ................... -
Page 6: Table Of Contents
Table of Contents Chapter 2 Installing the Media Converter ..............9 Verifying the Package Contents ................ 9 Planning the Installation................9 Selecting a Site ..................10 Reviewing Safety Guidelines ..............11 Installing the Media Converter ............... 12 Warranty Registration ..................14 Chapter 3 Troubleshooting .................... -
Page 7: Preface
Preface This guide contains instructions on how to install the AT-MC1004 and the AT-MC1005/x Series Gigabit Ethernet Media Converters. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com provides you with an easy way to access the most recent documentation and technical information for all of our products. -
Page 8: Contacting Allied Telesyn Technical Support
Preface Contacting Allied Telesyn Technical Support You can contact Allied Teleysn technical support online or by telephone or e-mail. Online Support You can request technical support online accessing the Knowledge Base at http://kb.alliedtelesyn.com. You can use the Knowledge Base to submit questions to our technical support staff and review answers to previously asked questions. -
Page 9: Returning Products
AT-MC1004 and AT-MC1005/x Series Installation Guide Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense. To obtain an RMA number, contact Allied Telesyn’s Technical Support at one of the following locations: North America... -
Page 11: Chapter 1 Overview
Chapter 1 Overview The AT-MC1004 and AT-MC1005/x Series Gigabit Ethernet Media Converters are designed to extend the distance of your network by converting Gigabit Ethernet data between twisted pair cabling and either multimode or single- mode fiber optic cabling. The AT-MC1004 media converter features a 1000Base-SX fiber optic port and a 1000Base-T twisted pair port. - Page 12 1000Base-SX AT-MC1004 550 m (1,804 ft) 1000Base-LX AT-MC1005/1 10 km (6.2 mi) AT-MC1005/2 20 km (12.4 mi) AT-MC1005/3 40 km (24.8 mi) AT-MC1005/4 70 km (43.4 mi) 1. Maximum distance may be less depending on the type of fiber optic cabling used with the port.
-
Page 13: Key Features
AT-MC1004 and AT-MC1005/x Series Installation Guide Key Features The media converters have the following key features: ❑ LEDs for unit and port status ❑ 1000Base twisted pair port with a maximum operating distance of 100 meters (328 feet) ❑ 1000Base fiber optic port with a maximum operating distance of 550 meters (1,804 feet) to 70 kilometers (43.4 miles) using single-mode or multimode fiber optic cabling, depending on the model ❑... -
Page 14: Fiber Optic Port
Overview Fiber Optic Port The 1000Base-SX port on the AT-MC1004 media converter has an SC connector and is designed to operate with multimode fiber optic cabling. This port has a maximum operating distance of 550 meters (1,804 feet) using 62.5/ 125 micron multimode fiber optic cable. -
Page 15: Smart Missinglink
AT-MC1004 and AT-MC1005/x Series Installation Guide For example, if the network twisted pair cable to the 1000Base-T port on the media converter were to fail, the unit would respond by dropping the link on the fiber optic port. In this way, the media converter notifies the end-node connected to the fiber optic port that the connection on the twisted pair port has been lost. -
Page 16: Half- And Full-Duplex Mode
Overview Half- and Full-Duplex Mode Duplex mode refers to the way an end-node sends and receives data on the network. An end-node can operate in either half- or full-duplex mode, depending on its capabilities. An end-node that is operating in half-duplex mode can either send data or receive data, but it cannot do both at the same time. -
Page 17: Network Topologies
AT-MC1004 and AT-MC1005/x Series Installation Guide Network Topologies The AT-MC1004 and AT-MC1005/x Series Gigabit Ethernet Media Converters can be used in two different network topologies: standalone and back-to-back. These network topologies are described below. Standalone Topology A standalone topology uses only one media converter between the end-nodes. Figure 4 illustrates a standalone topology that uses two AT-MC1005/1 media converters to interconnect three remote campuses. -
Page 18: Back-To-Back Topology
Overview Back-to-Back Topology In some network configurations you may want to interconnect two media converters in what is referred to as a back-to-back topology. In this topology, the media converters not only extend the distance of your network but also convert the fiber optic cable from twisted pair to fiber optic and back again. -
Page 19: Installing The Media Converter
Chapter 2 Installing the Media Converter Verifying the Package Contents Make sure the following items are included in your media converter package. If any item is missing or damaged, contact your Allied Telesyn sales representative. ❑ One AT-MC1004 or AT-MC1005/x Series Gigabit Ethernet Media Converter ❑... -
Page 20: Selecting A Site
7.5 dB at 850 nm multimode AT-MC1005/1 9/125 micron single-mode 10 km (6.2 mi) 17.0 dB at 1310 nm AT-MC1005/2 9/125 micron single-mode 20 km (12.4 mi) 18.0 dB at 1310 nm AT-MC1005/3 9/125 micron single-mode 40 km (24.8 mi) 18.0 dB at 1550 nm... -
Page 21: Reviewing Safety Guidelines
AT-MC1004 and AT-MC1005/x Series Installation Guide Reviewing Safety Guidelines Please review the following safety guidelines before you begin to install the media converter. Warning Class 1 laser device. Warning Do not stare into the laser beam. Warning Electric Shock Hazard: To prevent electric shock, do not remove the cover. -
Page 22: Installing The Media Converter
Installing the Media Converter Installing the Media Converter The following procedure explains how to install the media converter in your network. Note When two media converters are connected back-to-back with no twisted pair cables connected, the LNK LEDs on the fiber port may flash. This is normal and will not affect the normal operation of the units. - Page 23 AT-MC1004 and AT-MC1005/x Series Installation Guide Plug the AC/DC power adapter into an appropriate AC power outlet and insert the power plug into the DC receptacle located on the back of the unit. This step does not apply if you installed the unit in an AT-MCR12 chassis.
-
Page 24: Warranty Registration
Installing the Media Converter Warranty Registration When you finish installing the product, you should register your product by completing the enclosed warranty card and sending it in. -
Page 25: Chapter 3 Troubleshooting
Chapter 3 Troubleshooting Follow the guidelines below to test and troubleshoot the installation in the event a problem occurs. If the PWR LED is OFF, do the following: ❑ If the media converter is installed on a desktop, check to be sure that the power adapter is securely connected to a power outlet and that the power adapter cable is securely connected to the back of the media converter. - Page 26 Troubleshooting If the LNK LED for the fiber optic port is OFF, do the following: ❑ Verify that the end-node connected to the port is ON and is operating properly. ❑ Check that the fiber optic cable is securely connected to the fiber optic port on the media converter and on the remote end-node.
-
Page 27: Technical Specifications
Appendix A Technical Specifications Physical Dimensions: W x D x H 10.5 cm x 9.5 cm x 2.5 cm (4.125 in x 3.75 in x 1.0 in) Weight: 294 g (10.3 oz) Temperature Maximum Operating: 0° C to 40° C (32° F to 104° F) Maximum Storage: -25°... -
Page 28: Fiber Optic Port Specifications
Sensitivity (dBm) AT-MC1004 50/125 or 62.5/125 -4.0 to -9.5 -17.0 micron multimode AT-MC1005/1 9/125 micron -3.0 to -9.0 1310 -20.0 single-mode AT-MC1005/2 9/125 micron -4.0 to 1.0 1310 -21.0 single-mode AT-MC1005/3 9/125 micron -4.0 to 1.0 1550 -21.0 single-mode AT-MC1005/4 9/125 micron -3.0 to 2.0... -
Page 29: Rj-45 Pin Assignments
AT-MC1004 and AT-MC1005/x Series Installation Guide RJ-45 Pin Assignments Figure 8 shows the pin assignments of the media converter’s RJ-45 port. Pin 1 Pin 8 Figure 8 RJ-45 Pin Assignments Table 7 lists the RJ-45 connector pins and their signals for 1000Base-T. Table 7 RJ-45 Connector Pinouts Pinout Pair... -
Page 31: Translated Safety Statements
Appendix B Translated Safety Statements Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog. - Page 32 Gigabit Ethernet Media Converters Model Numbers: AT-MC1004, AT-MC1005/1, AT-MC1005/2, AT-MC1005/3, AT-MC1005/4 This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
- Page 33 AT-MC1004 and AT-MC1005/x Series Installation Guide RFI Emission EN55022 Class B Warning: In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Immunity EN55024 Electrical Safety EN60950, UL1950, CSA 950 Laser EN60825 Safety...
- Page 34 Translated Safety Statements Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. Hochfrequenzstörung EN55022 Klasse B Warnung: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen ergreifen. Störsicherheit EN55024 Elektrische Sicherheit EN60950, UL1950, CSA 950 Laser EN60825 Sicherheit...
- Page 35 AT-MC1004 and AT-MC1005/x Series Installation Guide Standarder: Dette produkt tilfredsstiller de følgende standarder. Radiofrekvens forstyrrelsesemission EN55022 Klasse B Advarsel: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger. Immunitet EN55024 Elektrisk sikkerhed EN60950, UL1950, CSA 950...
- Page 36 Translated Safety Statements Eisen: Dit product voldoet aan de volgende eisen. RFI Emissie EN55022 Klasse B Waarschuwing: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen. Immuniteit EN55024 Electrische Veiligheid EN60950, UL1950, CSA 950 Laser EN60825...
- Page 37 AT-MC1004 and AT-MC1005/x Series Installation Guide Normes: ce produit est conforme aux normes de suivantes: Emission d’interférences radioélectriques EN55022 Classe B Mise En Garde: dans un environnement domestique, ce produit peut provoquer des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures adéquates. Immunité...
- Page 38 Translated Safety Statements Standardit: Tämä tuote on seuraavien standardien mukainen. Radioaaltojen häirintä EN55022 Luokka B Varoitus: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin toimenpiteisiin. Kestävyys EN55024 Sähköturvallisuus EN60950, UL1950, CSA 950 Laser EN60825 Turvallisuus Varoitus: Luokan 1 Lasertuote.
- Page 39 AT-MC1004 and AT-MC1005/x Series Installation Guide Standard: Questo prodotto è conforme ai seguenti standard. Emissione RFI (interferenza di radiofrequenza) EN55022 Classe B Avvertenza: in ambiente domestico questo prodotto potrebbe causare radio interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati provvedimenti.
- Page 40 Translated Safety Statements Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. RFI stråling EN55022 Klasse B Advarsel: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler. Immunitet EN55024 Elektrisk sikkerhet EN60950, UL1950, CSA 950 Laser EN60825 Sikkerhet...
- Page 41 AT-MC1004 and AT-MC1005/x Series Installation Guide Padrões: Este produto atende aos seguintes padrões. Emissão de interferência de radiofrequência EN55022 Classe B Aviso: Num ambiente doméstico este produto pode causar interferência na radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas adequadas.
- Page 42 Translated Safety Statements Estándares: Este producto cumple con los siguientes estándares. Emisión RFI EN55022 Clase B Advertencia: en un entorno doméstico, este producto puede causar radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas que sean convenientes al respecto. Inmunidad EN55024 Seguridad eléctrica...
- Page 43 AT-MC1004 and AT-MC1005/x Series Installation Guide Standarder: Denna produkt uppfyller följande standarder. Radiostörning EN55022 Klass B Varning: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan tvinga användaren till att vidtaga erforderliga åtgärder. Immunitet EN55024 Elsäkerhet EN60950, UL1950, CSA 950 Laser EN60825 Säkerhet...