Allied Telesis AT-MC102XL Installation Manual

Allied Telesis AT-MC102XL Installation Manual

Version 3 fast ethernet media converters
Hide thumbs Also See for AT-MC102XL:

Advertisement

All manuals and user guides at all-guides.com
AT-MC101XL
AT-MC102XL
AT-MC103XL
AT-MC103LH
AT-MC103SC/FS3, FS4
AT-MC103ST/FS3, FS4
Version 3 Fast Ethernet Media Converters
Installation Guide
PN 613-10771-00 Rev D

Advertisement

Table of Contents
loading

Summary of Contents for Allied Telesis AT-MC102XL

  • Page 1 All manuals and user guides at all-guides.com AT-MC101XL AT-MC102XL AT-MC103XL AT-MC103LH AT-MC103SC/FS3, FS4 AT-MC103ST/FS3, FS4 Version 3 Fast Ethernet Media Converters Installation Guide PN 613-10771-00 Rev D...
  • Page 2 All manuals and user guides at all-guides.com Copyright  2000 Allied Telesyn International, Corp. 960 Stewart Drive Suite B, Sunnyvale CA 94086 USA All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesyn International, Corp. Ethernet is a registered trademark of Xerox Corporation.
  • Page 3: Safety Warnings

    408-730-0950 Declares that the Product: Fast Ethernet Media Converters Model Numbers: AT-MC101XL, AT-MC102XL, AT-MC103XL, AT-MC103LH, AT-MC103SC/FS3, AT-MC103ST/FS4, AT-MC103SC/FS4, AT-MC103ST/FS4 This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules. Operation is subject to the...
  • Page 4 All manuals and user guides at all-guides.com Laser EN60825 Power to the hub must be sourced only from the adapter. USA/CANADA Use a UL Listed/CSA Certified AC adapter of DC 12V, 500mA. EUROPE - EU Use TÜV licensed AC adapter of DC 12V, 500mA. Use a UK Safety Approved AC adapter of DC 12V, minimum 500mA.
  • Page 5: Table Of Contents

    All manuals and user guides at all-guides.com Table of Contents Safety Warnings .................... iii Welcome to Allied Telesyn ................. vii Where to Find Web-based Guides ..............vii Document Conventions ..................vii Contacting Allied Telesyn Technical Support..........viii Online Support ..................viii Telephone or Fax Support................
  • Page 6 All manuals and user guides at all-guides.com Appendix A Translated Electrical Safety and Emission Information ....21 Appendix B AT-MC100 Series Installation Guide Feedback ........35 Appendix C Technical Support Fax Order ..............37 Incident Summary..................37...
  • Page 7: Welcome To Allied Telesyn

    All manuals and user guides at all-guides.com Welcome to Allied Telesyn This guide contains instructions on how to install an AT-MC100 Series Fast Ethernet Media Converter. Where to Find Web-based Guides The Allied Telesyn web site at www.alliedtelesyn.com provides you with an easy way to access the most recent documentation and technical information for all of our products.
  • Page 8: Contacting Allied Telesyn Technical Support

    All manuals and user guides at all-guides.com Contacting Allied Telesyn Technical Support There are several ways to contact Allied Telesyn technical support: online, telephone, fax or e-mail. Online Support You can request technical support online by filling out the Technical Support Form at www.alliedtelesyn.com/forms/support.htm.
  • Page 9: Returning Products

    All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Returning Products Products for return or repair must first be assigned a Return Materials Authorization (RMA) number. A product sent to Allied Telesyn without a RMA number will be returned to the sender at the sender’s expense. To obtain an RMA number, contact Allied Telesyn’s Technical Support at one of the following locations: North America...
  • Page 10: For Sales Or Corporate Information

    All manuals and user guides at all-guides.com For Sales or Corporate Information Allied Telesyn International, Corp. Allied Telesyn International, Corp. 19800 North Creek Parkway, Suite 200 960 Stewart Drive, Suite B Bothell, WA 98011 Sunnyvale, CA 94086 Tel: 1 (425) 487-8880 Tel: 1 (800) 424-4284 (USA and Canada) Fax: 1 (425) 489-9191 Fax: 1 (408) 736-0100...
  • Page 11: At-Mc100 Series Fast Ethernet Media Converters

    All manuals and user guides at all-guides.com AT-MC100 Series Fast Ethernet Media Converters The AT-MC100 Series Fast Ethernet Media Converters include the following models: AT-MC101XL AT-MC103SC/FS3 AT-MC102XL AT-MC103ST/FS3 AT-MC103XL AT-MC103SC/FS4 AT-MC103LH AT-MC103ST/FS4 The AT-MC100 Series Fast Ethernet Media Converters are designed to extend the distance of your network by interconnecting LAN devices that are physically separated by large distances.
  • Page 12: Key Features

    Port 2 (100Base-FX) (100Base-TX) (100Base-FX) (100Base-TX) AT-MC101XL RJ-45 2 km (1.2 mi) 100 m (328 ft) AT-MC102XL RJ-45 2 km (1.2 mi) 100 m (328 ft) AT-MC103XL RJ-45 15 km (9.3 mi) 100 m (328 ft) AT-MC103LH RJ-45 40 km 100 m (328 ft) (24.8 mi)
  • Page 13: Status Leds

    All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Status LEDs Table 2 defines the system LEDs. Table 2 Status LEDs State Color Description Green A link has been established on the port. Green Data is being received on the port. Green Indicates that the unit is operating in full-duplex mode.
  • Page 14: Link Test/Missinglink Button

    All manuals and user guides at all-guides.com Link Test/MissingLink Button The Link Test/MissingLink button allows you to perform a link test on the ports on the media converter. This button also allows you to activate the MissingLink feature on the unit. Both features are describe in the following section.
  • Page 15: Auto-Negotiation Switch

    All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Auto-negotiation Button The auto-negotiation button, located on the front panel, disables the auto- negotiation feature (IEEE 802.3u) of the media converter. The media converter uses auto-negotiation to determine the duplex mode of the ports. The duplex mode refers to the manner in which a node sends and receives data on the network.
  • Page 16: External Ac/Dc Power Adapter

    All manuals and user guides at all-guides.com You can resolve the mismatch in one of two ways: Manually configure Unit 2, if possible, so that the port connected to the media converter is set to half-duplex. Disable auto-negotiation on the media converter using the auto- negotiation button.
  • Page 17: Network Topologies

    All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Network Topologies Figure 4 shows a network configuration where two AT-8224XL switches have been interconnected with an AT-MC102XL Media Converter. 100 meters AT-8224XL AT-MC102XL STATUS RS-232 TERMINAL PORT PORT ACTIVITY...
  • Page 18: Installing The Media Converter

    All manuals and user guides at all-guides.com Installing the Media Converter The following section explain how to install the media converter. The media converter can be installed either as a standalone unit (such as on a table) or in an AT-MCR12 chassis or in an AT-TRAY4 tray. Planning the Installation Be sure to observe the following guidelines when planning the installation of your media converter.
  • Page 19 Distance Loss Budget AT-MC101XL 50/125 or 62.5/125 2 km (1.2 mi) 13 dB at 1310 nm micron multimode AT-MC102XL 50/125 or 62.5/125 2 km (1.2 mi) 13 dB at 1310 nm micron multimode AT-MC103XL 9/125 micron 15 km (9.3 mi)
  • Page 20: Verifying The Package Contents

    All manuals and user guides at all-guides.com Verifying the Package Contents Make sure the following items are included in your media converter package. If any of the following items are missing or damaged, contact your sales representative. One AT-MC100 Series Fast Ethernet Media Converter Four protective feet (for standalone use only) External AC/DC power adapter This installation guide...
  • Page 21: Installing The Media Converter

    All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Installing the Media Converter The following procedure explains how to install the media converter as a standalone unit. If you are building a back-to-back installation, please review the following. See Figure 5 for an illustration of a back-to-back-media converter configuration.
  • Page 22 All manuals and user guides at all-guides.com Plug the AC/DC power adapter into an appropriate AC power outlet and insert the power plug into the DC receptacle located on the rear panel. (This step does not apply if you installed the unit in an AT-MCR12 chassis.) 12 V D C Figure 6 12 V DC Connector on Rear Panel...
  • Page 23: Testing The Installation

    All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide CLASS 1 100Base-FX 100Base-TX LASER PRODUCT DO NOT STARE INTO BEAM A/N ON A/N OFF MDI-X M/L ON LNK TST SINGLE MODE MC103SC/FS3 FAST ETHERNET MEDIA CONVERTER MDI-X Figure 7 MDI/MDI-X Switch 12.
  • Page 24 All manuals and user guides at all-guides.com Turn ON the nodes (such as the hubs or switches) that are connected to the media converter. Set the Link Test/MissingLink button on the media converter to the LNK TST (IN) position. Check the two LNK LEDs. They should be green, indicating that the media converter is receiving a signal from the nodes connected to the ports.
  • Page 25: Warranty Registration

    All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide If you are still experiencing problems after testing the installation, contact Allied Telesyn Technical Support. Technical support is offered online, telephone, fax or e-mail. Refer to “Contacting Allied Telesyn Technical Support” on page viii or visit our web site at www.alliedtelesyn.com for support information.
  • Page 26: Power Requirements

    Diameter (nm) (microns) Max. Avg. Min. AT-MC101XL 50/125 1310 nm -14.0 -20.3 -22.5 62.5/125 1310 nm -14.0 -16.8 -19.0 AT-MC102XL AT-MC103XL 9/125 1310 nm -8.0 -11.5 -15.0 AT-MC103LH 9/125 1310 nm -3.0 -5.0 AT-MC103SC/FS3 9/125 1310 nm -2.0 -4.0 AT-MC103ST/FS3...
  • Page 27 Optic Frequency Receive Power (dBm) Diameter (nm) (microns) Min. Typical Saturation AT-MC101XL 50/125 or 1310 nm -31.8 -34.5 -14.0 62.5/125 AT-MC102XL AT-MC103XL 9/125 1310 nm -31.0 -31.0 -8.0 AT-MC103LH 9/125 1310 nm -35.0 -38.0 AT-MC103SC/FS3 9/125 1310 nm -37.0 -37.0 -3.0...
  • Page 28 Signal Distance Distance Link Loss Spec. Spec. Budget (dB) (dB) AT-MC101XL 50/125 13.00 18.70 2 km (1.2 mi) AT-MC102XL 62.5/125 16.80 22.50 2 km (1.2 mi) AT-MC103XL 9/125 SMF 16.00 19.50 15 km (9.4 mi) AT-MC103LH 9/125 SMF 30.00 35.00 40 km (24.8 mi)
  • Page 29 All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Table 9 Fiber Optic Loss Specifications (Benchmarks) Fiber Type Fiber Optic Optical Typical Worst Case Bandwidth Diameter Frequency Loss Loss Factor (Mhz-km) (microns) Factor (dB/km) (dB/km) 50/125 850 nm 3.00 3.50 50/125...
  • Page 30 All manuals and user guides at all-guides.com...
  • Page 31: Translated Electrical Safety And Emission Information

    All manuals and user guides at all-guides.com Appendix A Translated Electrical Safety and Emission Information Important: This appendix contains multiple-language translations for the safety statements in this guide. Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch enthaltenen Sicherheitshinweise in mehreren Sprachen. Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af sikkerhedsadvarslerne i denne håndbog.
  • Page 32 408-730-0950 Declares that the Product: Fast Ethernet Media Converters Model Numbers: AT-MC101XL, AT-MC102XL, AT-MC103XL, AT-MC103LH, AT-MC103SC/FS3, AT-MC103ST/FS3 AT-MC103SC/FS4, AT-MC103ST/FS4 This product complies with FCC Part 15B, Class B Limits: This device complies with part 15 of the FCC Rules. Operation is subject to the...
  • Page 33 All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide SAFETY Laser EN60825 Warning Class 1 Laser product. Warning Do not stare into the Laser beam. At time of installation, the Fiber Optic Lasers comply with FDA Radiation Performance Standard 21CFR Subchapter J, applicable at date of manufacture. Use of controls or adjustments of performance or procedures other than those specified herein may result in hazardous radiation exposure.
  • Page 34 All manuals and user guides at all-guides.com Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen. Hochfrequenzstörung EN55022 Klasse B Störsicherheit EN50082-1 1997 ACHTUNG: Für dieses Produkt sind abgeschirmte Kabel erforderlich, damit den Richtlinien für Emission und Interferenzschutz entsprochen wird. Falls das Produkt mit nicht abgeschirmten Kabeln verwendet wird, können weitergehende Maßnahmen für die Korrektur von Interferenzproblemen auf Kosten des Benutzers notwendig werden.
  • Page 35 All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Standarder: Dette produkt tilfredsstiller de følgende standarder. Radiofrekvens forstyrrelsesemissionEN55022 Klasse B Immunitet EN50082-1 1997 ADVARSEL: Dette produkt skal bruges med afskærmede kabler for at overholde bestemmelserne vedrørende udstråling og støjimmunitet. Hvis det bruges med uafskærmede kabler, kan det blive påkrævet af brugeren at korrigere interferensproblemer for egen regning.
  • Page 36 All manuals and user guides at all-guides.com Eisen: Dit product voldoet aan de volgende eisen. RFI Emissie EN55022 Klasse B Immuniteit EN50082-1 1997 WAARSCHUWING: Om te voldoen aan de emissie- en immuniteitsnormen dient dit apparaat te zijn voorzien van afgeschermde kabels. Als het met niet-afgeschermde kabels wordt gebruikt, kan het zijn dat de gebruiker maatregelen moet treffen om interferentieproblemen voor eigen rekening op te lossen.
  • Page 37 All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Normes: ce produit est conforme aux normes de suivantes. Emission d'interférences radioélectriques EN55022 Classe Immunité EN50082 - 1 1997 AVERTISSEMENT: Il faut utiliser des câbles blindés pour ce produit afin de respecter les normes d’émission et d’immunité.
  • Page 38 All manuals and user guides at all-guides.com Standardit: Tämä tuote on seuraavien standardien mukainen. Radioaaltojen häirintä EN55022 Luokka B Kestävyys EN50082-1 1997 VAROITUS: Tämä tuote vaatii suojattuja kaapeleita toimiakseen emissio- ja häiriönsietostandardien mukaisesti. Jostuotetta käytetään ilman suojattuja kaapeleita, käyttäjä voi joutua korjaamaan häirinnän aiheuttaman ongelman omallakustannuksellaan.
  • Page 39 All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Standard: Questo prodotto è conforme ai seguenti standard. Emissione RFI (interferenza di radiofrequenza) EN55022 Classe Immunità EN50082-1 1997 AVVERTENZA: questo prodotto, se utilizzato con cavi schermati, è conforme alle norme sulle emissioni e sull’immunità.
  • Page 40 All manuals and user guides at all-guides.com Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer. RFI stråling EN55022 Klasse B Immunitet EN50082-1 1997 ADVARSEL: Dette produktet må brukes med vernede kabler for å tilfredsstille emisjons- og fritakelsesstandarder. Dersom produktet brukes med uvernede kabler, må...
  • Page 41 All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Padrões: Este produto atende aos seguintes padrões. Emissão De Interferência De Radiofrequência EN55022 Classe Imunidade EN50082-1 1997 ADVERTÊNCIA: Este produto requer a utilização de cabos blindados para cumprimento dos standards de limites de emissão e imunidade. Se o produto for utilizado com cabos não blindados, o utilizador poderá...
  • Page 42 All manuals and user guides at all-guides.com Estándares: Este producto cumple con los siguientes estándares. Emisión RFI EN55022 Clase Inmunidad EN50082-1 1997 ADVERTENCIA: Este producto exige cables protectores para ajustarse a las normas de emisión e inmunidad. Si se utiliza con cables sin protección, el usuario tendrá que correr con los gastos por las medidas a tomar en caso de problemas de interferencias.
  • Page 43 All manuals and user guides at all-guides.com AT-MC100 Series Installation Guide Standarder: Denna produkt uppfyller följande standarder. Radiostörning EN55022 Klass B Immunitet EN50082-1 1997 VARNING! Denna produkt kräver skärmade kablar för att uppfylla standardkraven för emission och immunitet. Om den används med oskärmade kablar kan användaren vara tvungen att vidta åtgärder på...
  • Page 44 All manuals and user guides at all-guides.com...
  • Page 45: At-Mc100 Series Installation Guide Feedback

    All manuals and user guides at all-guides.com Appendix B AT-MC100 Series Installation Guide Feedback Please tell us what additional information you would like to see discussed in this guide. If there are topics you would like information on that were not covered in this guide, please photocopy this page, answer the questions and fax or mail this form back to Allied Telesyn.
  • Page 46 All manuals and user guides at all-guides.com...
  • Page 47: Technical Support Fax Order

    All manuals and user guides at all-guides.com Appendix C Technical Support Fax Order Name _________________________________________________________________ Company ______________________________________________________________ Address _______________________________________________________________ City______________________ State/Province_______________________________ Zip/Postal Code ________________ Country_______________________________ Phone______________________________ Fax _______________________________ Incident Summary Model number of Allied Telesyn product I am using ________________________ Firmware release number of Allied Telesyn product _______________________ Other network software products I am using (e.g., network managers) ______________________________________________________________________...
  • Page 48 All manuals and user guides at all-guides.com...

Table of Contents