Aiphone GT SYSTEM Installation Manual
  1. Manuals
  2. Brands
  3. Aiphone Manuals
  4. Intercom System
  5. GT SYSTEM
  6. Installation manual

Aiphone GT SYSTEM Installation Manual

Apartment intercom system
Hide thumbs Also See for GT SYSTEM:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual , User Manual
0311 A OI
6(59,&( 0$18$/
GT SYSTEM
Apartment Intercom System
Installation manual

Advertisement

Table of Contents
loading

Related Manuals for Aiphone GT SYSTEM

Summary of Contents for Aiphone GT SYSTEM

  • Page 1 0311 A OI 6(59,&( 0$18$/ GT SYSTEM Apartment Intercom System Installation manual...

  • Page 2: General Precautions

    11. Do not put anything on or cover the unit with cloth, etc. Fire or unit trouble could result. 12. For power supply, use Aiphone power supply model or model specified for use with system. If non-specified product is used, fire or malfunction could result.
  • Page 3 - 3 -...

  • Page 4: System Configurations

    SYSTEM CONFIGURATIONS Standard system configuration This system is constructed with a 2-line communication system and a 2-line video system and requires minimal work for installation. The system is constructed with video trunk lines consisting of a maximum of 6 trunks from the video bus control system and communication trunk lines that use a distribution point from a bus control unit.
  • Page 5 Expanded system configuration diagram The wiring of the sub trunk line is the same as the standard system. Common area Audio signal line (1) Video signal line (1) Power supply line (1) Residence trunks Residence trunks Residence trunks Residence trunks #1 #2 #3 #4 #5 #1 #2 #3 #4 #5 #1 #2 #3 #4 #5...
  • Page 6 Residential station configuration For wiring from the control units to each residence, station-to-station wiring or star wiring using a 4-way video junction unit is possible. Mixing on the same trunk line is not possible. Audio signal line (1) Video signal line (1) Power supply line (1) Trunk line #1 Trunk line #2...
  • Page 7 Video door station or doorbell GT-2C-L, GT-2C GT-D Sub master monitor station AIPHONE JF-DVF GT-2H-L, GT-2H PS24 Power supply-related [When sub master monitor stations are connected] If even just one sub master monitor station is connected, it is possible to supply power to up to 2 residences with 1 power supply.

  • Page 8: Wiring Distance

    Wiring distance Standard system Expanded system Each Each residence (with recording function) residence Each residence PS24 Each residence PS24 Each residence PS24 PS24 PS24 Entrance station Entrance station PS24 PS24 PS24 PS24 Each Each The GT-VBC can be used as an extension adaptor as well (2 residence residence units per trunk line).
  • Page 9 Wire diameter 0.65 mm 0.8 mm 1.0 mm Wiring distance (22 AWG) (20 AWG) (18 AWG) GT-BC - DP *2 3 m (10') 5 m (16') 5 m (16') Entrance station - DP *2 150 m (490') 300 m (980') 300 m (980') Entrance station - GT-VBC 150 m (490')
  • Page 10 COMPONENTS Entrance Station (Unit type) Panel Module Speech module (guidance-enabled Speech module panel type) (guidance-enabled type) GT-DP-L GT-DA-L (connector included) Speech module Speech module panel GT-DA GT-DP (connector included) Camera module Camera module panel GT-VA GT-VP (connector included) 1-call button panel 2-call button panel GF-1P GF-2P...
  • Page 11 Mounting parts 4-module front Mounting bracket frame (included with Screws GT-4F GT-4F) 3-module front Mounting bracket 2-module front Mounting bracket frame (included with frame (included with GF-2F) GF-3F GF-3F) GF-2F Joint pipe 2-module back 4-module back box 3-module back box GT-4B GF-3B GF-2B...

  • Page 12: Residential Station

    Entrance Station (Integrated type) USB cable A-B type (1 m) Flush mount entrance station (name scrolling, guidance-enabled, VIGIK-linked type) GT-DMV Flush mount entrance station (name scrolling, guidance-enabled) GT-DM Screws Special screwdriver Bus control unit etc. • Installation manual • Entrance station + security guard station operation manual •...

  • Page 13: Door Station

    Residential station GT-1A Wood mounting screws Screws Residential station GT-1D Optional handset GT-HS Residential monitor station with handset Option connector GT-1M-L Door station For door stations other than the GT-D, see the instruction manual for that door station. Wood mounting screws Door station GT-D Screws...

  • Page 14: Mounting Locations

    MOUNTING Mounting locations • For video entrance stations and video door stations, the picture quality of residential station monitoring is affected by the nature of the external light from above and the surrounding area of the built-in cameras, so do not install these stations in the types of locations shown below. •...
  • Page 15 Mounting positions and image view area When using the camera module, if the rain hood is attached a portion of it will show up in the camera display. Mounting position 1350 mm (4' 4") Mounting position 1550 mm (5' 1") Wide picture Up/Down Approx.
  • Page 16 Assemble the module. • For the useable modules, see 2-1. • The GT-SW can have up to 6 modules. To connect 7 or more modules or to increase the light intensity, please con- tact Aiphone. Special screwdriver (enclosed with GT-BC) Mount each module panel to the front frame.
  • Page 17 Remove the terminal cover. From the speech module to the next module, insert the attached connector into the socket. Make sure to run the cable under the terminal cover for protection. Connect the connectors between the modules with cables. Mount modules on the back boxes. Example of interconnection of modules Use the GF-C to connect to the name scrolling module.
  • Page 18 Entrance Station (Integrated type) Open the cover and connect the wiring to the terminal block. Insert the wire into the direct terminal. If it is difficult to insert the wire, insert it while pressing the release button. Close the cover until it clicks into place. Flush mount back box Unit...
  • Page 19 Bus control unit, 4-way video junction unit and power supply DIN rail mounting The length of the connecting cable between the GT-BCX and GT-VBX is 40 cm. Therefore, mount them adjacently to each other. Mount the unit on the DIN rail. Click the unit into place. When removing the unit, pull the lock release lever down.
  • Page 20 Residential station Mounting screws ×4 3-gang box 83.5 mm (3-5/16") Mounting bracket 1. Press the release button (to insert or remove the wire). 2. Insert the cable into the terminal. • To remove the terminal block, slide the terminal block and pull it out. •...
  • Page 21 Mount the mounting bracket on the 1-gang box or round back box. Mounting bracket Mounting screws 1-gang box 83.5 mm (3-5/16") 60 mm (2-3/8") Round back box Mounting screws Connect the wiring to the terminal block. • To remove the terminal block, slide the terminal block and pull it out. •...
  • Page 22 Chassis Mount the station unit to the chassis or mounting bracket. 1-gang box Screws 83.5 mm (3-5/16") Connect the wiring to the terminal block. GT-1M-L: • To remove the terminal block, slide the terminal block and pull it out. • Strip away the jacket of the cable and insert all wires into the slots in an orderly 60 mm (2-3/8") fashion.
  • Page 23 Security guard station Peel off the protection film on the display. Desk-top mounting using the GFW-S stand Screws included with GFW-S (×4) Separate the mounting bracket and the protective cover from the Mounting Protective cover Mounting bracket back of the unit. bracket Mount the mounting bracket to the GFW-S as shown in the draw- ing.
  • Page 24 WIRING Standard system for common area Put each piece of wiring in a separate sheath as shown in the diagram below. Entrance station Entrance station #1 to #3 Ex.) Unit type Brown NTSC (+) Surveillance camera Red NTSC (-) External signaling relay GT-DA-L/GT-DA SW2: 2~4 Blue...
  • Page 25 Bus control unit PS24 230 V AC Video bus control unit GT-VBC IN 230V~ 50/60Hz 2A - + 24V DC 100V - 240V - 50/60 Hz 24 V DC2A Residence trunk (1) Residence trunk (2) Residence trunk (3) Residence trunk (4) Residence trunk (5) Residence trunk (6) PS24...
  • Page 26 Standard system for residence (station-to-station wiring) Residential station Residential station GT-2C-L GT-2C GT-1C-L Audio only Terminal setting: GT-1C For the terminating Door residential station, turn Terminal setting: GT-1A GT-1D station SW1 to the [A] side. For the terminating residential station, turn SW1 to the [A] side.
  • Page 27 Standard system for residence (homerun wiring) Residential station Residential station B1 B2 R1 R2 B1 B2 R1 R2 GT-4Z Terminal setting: For the terminating 4-way video junction unit, turn SW1 to the "A" side. In this case, 1 residential station can be connected to [LINE OUT].

  • Page 28: Expanded System

    Expanded system Common trunk line system (1) Expanded video bus control unit Entrance station GT-VBX #1 to #3 Ex.) Unit type GT-DA-L/GT-DA SW2: 2~4 1 2 3 4 1 2 3 4 PS24 1 2 3 4 Entrance station Sub trunk line #4 to #6 system (1) B Ex.) Unit type...
  • Page 29 Put each piece of wiring in a separate sheath as shown in the diagram below. Sub trunk line system (1) A Homerun wiring Trunk line #1 Trunk line #2 Trunk line #3 to #6 Each Each 4-way video Video bus control unit Station-to-station residence residence...
  • Page 30 Expanded video bus control unit GT-VBX • Connector cable length: 40 cm Expanded bus control unit GT-BCX • There are 4 groups each of R1 and R2 terminals on each trunk line terminal including COMMON1, COMMON2, SUB1A, SUB1B, SUB2A, and SUB2B.

  • Page 31: External Signaling Relay Connection

    Emergency alarm Video out The emergency alarm switch can be connected. Video can be output to DVRs etc. N/C contact (locked type) (NTSC, 1 Vp-p/75 ) Wiring distance: 3 m DC 12 V/0.1 A or higher NOTES: When a video signal is output, residential stations may pro- duce a sound depending on the installation environment.

  • Page 32: Table Of Contents

    SETTINGS (COMMON AREA) Setting list Perform the following settings at an entrance station or security guard station. Depending on the setting item, some items are set by switching DIP switches and some are set using the program mode menu. After any DIP switches are switched or any changes are made in the program mode, turn the power supply off and on again. In some cases, the settings may not be changed.
  • Page 33 Programming cannot be performed from a security guard station if there is a record of an emergency alarm. Check on the display that the unit is in the standby mode. When performing the initial settings, "WELCOME" will display at the entrance station and "AIPHONE" will display on the security guard •...

  • Page 34: Entrance Station And Security Guard Station Id Setting

    Entrance station and security guard station ID setting IDs for entrance stations and security guard stations are set using the DIP switches of units. The setting shown with "#1" is the setting at the time of shipment. When installing multiple entrance stations and security guard stations, make sure to set IDs.

  • Page 35: Writing Resident Information

    Writing resident information If the entrance station is a 10 key type or a GT-MK, program the resident information (names and room numbers) before performing the system settings. Up to 500 resident information entries can be registered. Programming with a PC •...

  • Page 36: Manual Setting Of Residence Ids

    Manual setting of residence IDs Residential station IDs are automatically assigned during link setting. However, with the GT-2C-L/GT-2C and GT-1C-L/GT-1C units only, they can be set manually using the switches on the unit. All are set to OFF in the initial settings. When replacing a residential station due to malfunction, resetting the link is unnecessary as the link can be maintained by adjusting the switches.
  • Page 37 Performing settings from an entrance station Check that all units are mounted and wired correctly, and then turn on the power switch of the GT-BC. GT-BC With the GT-DA/GT-DA-L, loosen the base screw of the frame GT-DMV/GT-DM and open and remove the front panel. Remove the rubber cap and use a fine screwdriver to push the program switch.
  • Page 38 Press the OFF button to finish programming. With the handset type module, return the handset. Repeat steps 3 to 6 to program all residential stations. GT-DMV/GT-DM Press the program switch of the GT-DA-L/GT-DA to finish programming. The in use LED will go out. For the GT-DMV/GT-DM, press the button.
  • Page 39 Performing settings from a security guard station Check that all units are mounted and wired correctly, and then turn on the power switch of the GT-BC. GT-BC GT-MK Enter the program mode at the GT-MK and select "PRO- PROGRAMMING << GRAMMING"...

  • Page 40: Transferring Link Information

    Transferring link information Transfer link setting information set at an entrance station or security guard station to other entrance stations and security guard stations. Enter the program mode and select "TRANSFER DATA". GT-NS-V/GT-NS, GT-MK GT-DMV/GT-DM TRANSFER DATA MENU CHANGE GREETING PROGRAMMING TRANSFER DATA :ENTER...

  • Page 41: Link Check

    Link check Performing settings from an entrance station (Unit type) Press the program switch of the GT-DA-L/GT-DA for at least 5 seconds. The in use LED will light up after blinking. GT-SW: Press the relevant call button. GT-NS-V/GT-NS: Select the room and press the button.

  • Page 42: Setting The Input Timeout Timer

    5-10 Setting the input timeout timer Enter the program mode with the GT-NS-V/GT-NS, GT-DMV/GT-DM or GT-MK and select "SET TIMER". Operation timer: If the operation panel is not operated for a certain period of time, the system returns to standby mode. The initial setting is 15 •...

  • Page 43: Display Language Selection

    5-11 Display language selection Start the program mode with the GT-NS-V/GT-NS, GT-DMV/GT-DM or GT-MK and select "SELECT LANGUAGE". The initial setting is English. Select English, French, German, Spanish, Dutch, or Italian. GT-NS-V/GT-NS, GT-MK GT-DMV/GT-DM SELECT LANGUAGE MENU SELECT LANGUAGE GUIDE LANGUAGE CHANGE ID CODE :ENTER SELECT LANGUAGE...

  • Page 44: Setting Messages And The Standby Screen

    5-13 Setting messages and the standby screen GT-NS-V/GT-NS: Use 3 of SW1 to change the greeting message to an operation message. The initial setting is for a greeting message. GT-NS-V/GT-NS 1 2 3 4 Operation message Greeting message GT-DMV/GT-DM: Start the program mode and select "STANDBY SCREEN". GT-DMV/GT-DM MENU STANDBY SCREEN...

  • Page 45: Room Number Display Setting

    5-14 Room number display setting Set the entrance station display to show room numbers or to display only resident names. The initial setting is for the room number to also display. GT-NS-V/GT-NS: Switch this setting with 2 of SW1. GT-NS-V/GT-NS 1 2 3 4 Display only resident name Display room number also...

  • Page 46: Setting The Sort Order For Searching

    5-16 Setting the sort order for searching Select either name order or room number order for searching at entrance stations and security guard stations. The initial setting is name order. GT-NS-V/GT-NS, GT-DMV/GT-DM, GT-MK: Enter the program mode and select "SORT SETTING". SORT SETTING MENU STANDBY SCREEN...

  • Page 47: Access Code Setting

    5-17 Access code setting Up to 500 access codes can be set for door release at an entrance station. The number of digits for access codes can be set anywhere in the range from 4 to 6. The initial setting is 4 digits. * Setting the access code number of digits GT-NS-V/GT-NS, GT-DMV/GT-DM: Enter the program mode and select "ACCESS CODE".

  • Page 48: Entrance Monitor Setting

    5-18 Entrance monitor setting Monitoring with the entrance station camera from a residential station can be set to be possible or not possible. The initial setting makes this not pos- sible. GT-DA-L/GT-DA: Switch this setting with 1 of SW2. GT-DA-L/GT-DA 1 2 3 4 Monitoring possible Monitoring not possible...

  • Page 49: Surveillance Camera Switching Setting

    5-20 Surveillance camera switching setting Select "LIGHT CONTROL" or "CCTV SWITCH" for the operation performed when the light button on a residential station is pressed. The initial set- ting is OFF ("LIGHT CONTROL"). GT-VA: Switch this setting with 2 of SW1. GT-VA 1 2 3 4 Surveillance camera...

  • Page 50: Lcd Operation Mode Setting

    5-22 LCD operation mode setting The LCD screen automatic ON function can only be set with the GT-DMV/GT-DM. The initial setting is sensor mode. Sensor mode: The LCD will automatically turn ON due to the sensor when a person approaches. The detection distance changes depending on the •...

  • Page 51: Entrance Zoom Picture Pre-Set

    5-25 Entrance zoom picture pre-set The picture can be set to display at the position set for zoom picture display when a residential station is called from an entrance station. The initial set- ting is for display at the center. Perform this setting in the pre-set mode.

  • Page 52: Visibility Settings (Daytime Only)

    Quit the pre-set mode Quit the pre-set mode Press the button to register the pre-set position. Press the button to register the pre-set position. Press the button to return to the menu. Press the program switch of the GT-DA-L/GT-DA to finish programming.

  • Page 53: Entrance Night Illumination Setting

    5-27 Entrance night illumination setting At night, the illuminator LED automatically lights up during an entrance station call. It can be set to always be off if night illumination is unnecessary or it is too bright. The initial setting is for the LED to automatically light up. GT-VA, GT-DMV/GT-DM: Switch this setting with 1 of SW1.
  • Page 54 Setting (GT-2C-L/GT-2C) 1. See the operation manual included with the GT-2C-L/GT-2C for the name and operating method for each part. 2. Actual screens may vary depending on the system. 3. When settings are changed, turn the unit power supply off and on again. In some cases, the settings may not be changed. How to use the MENU In the standby mode, press the [ ADJUST] button and [...
  • Page 55 Emergency input settings Set emergency input to be enabled or disabled. After performing steps 1 in section 6-1, select "ALARM IN- Select "DISABLE", "N/O", or "N/C" in the "ALARM INPUT" screen. Press the [ MENU] button to complete the settings PUT"...
  • Page 56 Utility sensor setting (detection method) Security sensor (alarm transfer) When "UTILITY" is selected, select "N/O" or "N/C" in the When [SECURITY] is selected, in the [EXTERNAL INPUT "UTILITY-SENSOR DETECTION METHOD" screen and SETTING] screen, select [ALARM TRANSFER] and press press the [ MENU] button.
  • Page 57 Doctor call setting Set Doctor call to be enabled or disabled. After performing steps 1 in section 6-1, select "DOCTOR Select from "ENABLE/DISABLE" in the "DOCTOR CALL" CALL" in the "INSTALLATION" screen and press the [ screen. Press the [ MENU] button to complete the settings.

  • Page 58: Technical Precautions

    Initializing All settings can be restored to their condition at the time of purchase. After performing steps 1 in section 6-1, select "INITIALIZE" 1. Recorded pictures are erased and settings are reset. in the "INSTALLATION" screen and press the [ MENU] 2.
  • Page 59 - 59 -...
  • Page 60 Aiphone warrants that its products have no material or workmanship defects under normal use conditions for two years after delivery to the end user. Aiphone will perform repair or replacement free of charge if the product is defective and the warranty applies to the defect. Aiphone reserves unto itself the sole right to make the final decision whether there is a defect in materials and/or workmanship and whether or not the product is under warranty.

Table of Contents