Sensor Installation Or Replacement - Teledyne TED 60-T Operator's Manual

2 Operations 2 Operations 2 Operations
2 Operations 2 Operations
CAUTION: CAUTION: USE ALKALINE BATTERIES ONLY. OTHER TYPES MAY GIVE ERRONEOUS USE ALKALINE BATTERIES ONLY. OTHER TYPES MAY GIVE ERRONEOUS
CAUTION: CAUTION: USE ALKALINE BATTERIES ONLY. OTHER TYPES MAY GIVE ERRONEOUS CAUTION: USE ALKALINE BATTERIES ONLY. OTHER TYPES MAY GIVE ERRONEOUS USE ALKALINE BATTERIES ONLY. OTHER TYPES MAY GIVE ERRONEOUS
READINGS. READINGS. READINGS. READINGS. READINGS.
If "BAT" appears in the upper left-hand corner of the LCD, the battery needs
replacing.

Sensor Installation or Replacement

Sensor Installation or Replacement
Sensor Installation or Replacement Sensor Installation or Replacement Sensor Installation or Replacement
NOTE: NOTE: The T-7 oxygen sensor must be installed before the TED 60T will operate. NOTE: The T-7 oxygen sensor must be installed before the TED 60T will operate. The T-7 oxygen sensor must be installed before the TED 60T will operate. The T-7 oxygen sensor must be installed before the TED 60T will operate.
NOTE: NOTE: The T-7 oxygen sensor must be installed before the TED 60T will operate.
NOTE: NOTE: When a new sensor is installed, typically, the unit is suitable for use immediately When a new sensor is installed, typically, the unit is suitable for use immediately
NOTE: NOTE: NOTE: When a new sensor is installed, typically, the unit is suitable for use immediately When a new sensor is installed, typically, the unit is suitable for use immediately When a new sensor is installed, typically, the unit is suitable for use immediately
after installation. after installation. after installation. after installation. after installation.
CAUTION: CAUTION: CAUTION: Do not autoclave the sensor. See page 2.4, Sterilization. Do not autoclave the sensor. See page 2.4, Sterilization. Do not autoclave the sensor. See page 2.4, Sterilization.
CAUTION: CAUTION: Do not autoclave the sensor. See page 2.4, Sterilization. Do not autoclave the sensor. See page 2.4, Sterilization.
1. Remove the new sensor from its protective bag. Inspect the sensor for
damage or electrolyte leakage. If the sensor is damaged, obtain a replace-
ment. Do not use the defective sensor as it may damage the unit.
CAUTION: CAUTION: CAUTION: The T–7 sensor electrolyte is caustic. Do not let it come in contact with skin. The T–7 sensor electrolyte is caustic. Do not let it come in contact with skin. The T–7 sensor electrolyte is caustic. Do not let it come in contact with skin.
CAUTION: CAUTION: The T–7 sensor electrolyte is caustic. Do not let it come in contact with skin. The T–7 sensor electrolyte is caustic. Do not let it come in contact with skin.
If it does, flush affected area with water. Do not attempt to open or repair the If it does, flush affected area with water. Do not attempt to open or repair the
If it does, flush affected area with water. Do not attempt to open or repair the If it does, flush affected area with water. Do not attempt to open or repair the If it does, flush affected area with water. Do not attempt to open or repair the
sensor. Check the sensor regularly for leaks. Leaking or exhausted sensors sensor. Check the sensor regularly for leaks. Leaking or exhausted sensors
sensor. Check the sensor regularly for leaks. Leaking or exhausted sensors sensor. Check the sensor regularly for leaks. Leaking or exhausted sensors sensor. Check the sensor regularly for leaks. Leaking or exhausted sensors
should be disposed of in accordance with local regulations. Consult the should be disposed of in accordance with local regulations. Consult the
should be disposed of in accordance with local regulations. Consult the should be disposed of in accordance with local regulations. Consult the should be disposed of in accordance with local regulations. Consult the
Material Safety Data Sheet in the Appendix. Material Safety Data Sheet in the Appendix. Material Safety Data Sheet in the Appendix. Material Safety Data Sheet in the Appendix. Material Safety Data Sheet in the Appendix.
2. Plug the end of the coiled cable into the telephone jack receptacle on the end
of the T-7 sensor, observing proper key orientation. The jack will only fit
one way, so if it does not fit, rotate it until it slides in easily.
NOTE: NOTE: NOTE: NOTE: NOTE: If the TED 60T is used for diffusion sampling (i.e., incubators, tents, etc.), the If the TED 60T is used for diffusion sampling (i.e., incubators, tents, etc.), the If the TED 60T is used for diffusion sampling (i.e., incubators, tents, etc.), the If the TED 60T is used for diffusion sampling (i.e., incubators, tents, etc.), the If the TED 60T is used for diffusion sampling (i.e., incubators, tents, etc.), the
plastic flow diverter must be removed from the T-7 sensor. If the sensor is used plastic flow diverter must be removed from the T-7 sensor. If the sensor is used plastic flow diverter must be removed from the T-7 sensor. If the sensor is used plastic flow diverter must be removed from the T-7 sensor. If the sensor is used plastic flow diverter must be removed from the T-7 sensor. If the sensor is used
in breathing circuits, etc., the diverter must be used. in breathing circuits, etc., the diverter must be used. in breathing circuits, etc., the diverter must be used.
in breathing circuits, etc., the diverter must be used. in breathing circuits, etc., the diverter must be used.
2-2
Micro-Fuel Cell
Flow
Diverter
Sensing
Surface
Teledyne Analytical Instruments
Tee
Adapter