Table of Contents
Advertisement
Menu operation (continued)
5. NETWORK menu
M
e
n
u
o
t p
o i
n
PROJECTOR NAME
NETWORK PASSWORD
OK
IP CONFIG
DHCP
IP ADDRESS
SUBNET MASK
DEFAUL T GA TEWAY
MAC ADDRESS
PJLink CERTIFICA TION
ON
N
E
T
W
O
R
K
R
E
S
E
T
6. INFORMATION menu
M
e
n
u
o
t p
o i
n
This menu shows a lamp operating time (hour) calculated assuming that LAMP MODE is LOW.
•
•
LAMP TIME (LOW)
•
N I
P
U
T
n I
RESOLUTION
Indicates the resolution of the currently projected video signal.
VERTICAL FREQUENCY
Indicates the vertical frequency of the currently projected video signal.
HORIZONT AL FRE-
Indicates the horizontal frequency of the currently projected video signal.
QUENCY
SYNC. TYPE
Indicates the type of the sync signal for the currently projected video signal.
S
e
t t
n i
g
Displays PROJECTOR NAME. Displays PROJECTOR NAME in
*****
...
blank when PROJECTOR NAME is not set.
Set PROJECTOR NAME. Enter up to 15 characters (alphabets or
SET
numeric characters).
Set the password for Web control or PJLink certification.
OK
Select this setting for IP Configuration.
Use this setting when you obtain IP CONFIG automatically by
ON
/ OFF
DHCP server.
Displays IP ADDRESS. However, IP ADDRESS is not set as factory
***,***,***,***
default, and cannot be displayed.
Set IP ADDRESS. When DHCP is se t to ON, you cannot change
SET
this setting.
Displays SUBNET MASK. However, SUBNET MASK is not set as
***,***,***,***
factory default, and cannot be displayed.
Set SUBNET MASK. When DHCP is set to ON, you cannot change
SET
this setting.
Displays DEFAULT GA TEWAY . However, DEFAUL T GA TEWAY is
***,***,***,***
not set as factory default, and cannot be displayed.
Set DEFAUL T GA TEWAY . When DHCP is set to ON, you cannot
SET
change this setting.
xx-xx-xx-xx-xx-xx
Displays MAC ADDRESS.
/ OFF
Use this setting for PJLink Certification.
O
K
R
e
e s
s t
When the LAMP MODE is STANDARD, this menu shows a longer lamp operating time than
the actual time. (See page 38 for the interval of lamp replacement.)
When the lamp operating time is 0 to 10 hours, "0H" is displayed. When the lamp operating
time exceeds 10 hours, the actual hours are displayed.
When the lamp operating time reaches 3750 hours, the bar turns yellow. When it reaches
4750 hours, the bar turns red.
(The lamp lifetime is 5000 hours.)
i d
a c
e t
s
h t
e
n
a
m
e
f o
h t
e
t
r e
m
n i
l a
o t
F
e
ature description
h t
e
N
e
w t
o
k r
S
t e
n i t
. g
F
e
a
u t
e r
d
e
s
c
i r
t p
o i
n
w
h
c i
h
h t
e
c
r u
e r
n
y l t
p
o r
e j
c
e t
d
v
d i
e
EN-26
NETWORK
NETWORK
IP CONFIG
NETWORK IP CONFIG
menu
INFORMATION
o
s
g i
n
l a
s i
b
e
n i
g
n i
p
u
. t
R G B
H V
opt.
PROJECTOR
SET
NAME
NETWORK
OK
PASSWORD
OK
IP CONFIG
PJLink
ON
CERTIFICATION
NETWORK RESET
OK
opt.
DHCP
ON
192.168.0.10
IP ADDRESS
SUBNET MASK
255.255.255.0
DEFAULT
10.132.1.1
GATEWAY
MAC ADDRESS
xx-xx-xx-xx-xx-xx
opt.
0 H
LAMP TIME (LOW)
INPUT
COMPUTER2
RESOLUTION
1024x768
VERTICAL
75.04 Hz
FREQUENCY
HORIZONTAL
60.02 KHz
FREQUENCY
SYNC. TYPE
5wire
- Quick Links:
- Lamp Replacement
- Troubleshooting
- Specifications
Hide quick links:
Advertisement
Table of Contents
