Direct Power Off - Mitsubishi Electric DLP FD730U User Manual

Basic operation (continued)
• To avoid permanently imprinting a fixed image
onto your projector, please do not display the
same stationary images for long period.
6. Adjust the image size by turning the zoom ring.
7. Adjust the vertical position of the displayed image
by turning the LENS SHIFT dial.
If necessary, adjust the focus and zoom again.
When fine streaks are seen on projected
images
This is due to interference with the screen surface and
is not a malfunction. Replace the screen or displace
the focus a little.
Power-off
Use the following procedure to turn off the projector.
The lamp may deteriorate if the projector is powered
off and on repeatedly within 30 minutes after the lamp
is lighted.
1. Press the POWER button on the control panel or
the STANDBY button on the remote control.
• The message "POWER OFF? YES : PRESS
AGAIN" appears on the screen.
• To cancel, press any button except the POWER
button. (Some buttons on the remote control
don't function for cancel.)
2. Press the POWER button on the control panel or
the STANDBY button on the remote control within
10 seconds again.
• The lamp will go out and the STATUS indicator
will start blinking.
3. Wait about 90 seconds for the STATUS indicator to
be turned off.
4. Unplug the power cord.
• The POWER indicator will go out.
• If the power cord should be unplugged
accidentally while either the STATUS indicator is
blinking or the lamp is on, allow the projector to
cool down for 10 minutes with the power off. To
light the lamp again, press the POWER button
(or ON button). If the lamp doesn't light up
immediately, repeat pressing the POWER button
(or ON button) two or three times. If it should still
fail to light up, replace the lamp.
Important:
• When storing the projector in the carrying case, the
lens should face up.
Before carrying the projector, rotate the focus ring
and zoom ring to adjust the lens to the shortest.
This prevents the possible damages of the lens.

Direct Power OFF

You can turn off this projector just by unplugging the
power cord without pressing the POWER button.
• Don't shut down the projector while the STATUS
indicator is blinking after the lamp lights up
because the lamp's life may be shortened.
• Don't turn the projector back on right after shutting
it down because the lamp's life may be shortened.
(Wait about 10 minutes before turning the projector
back on.)
• Before shutting down the projector, be sure to close
the menu screen. If you shut down the projector
without closing the menu, the setting data of the
menu may not be saved.
• If you shut down the projector while controlling
the projector using the network function, the
application software such as ProjectorView may
fail. For details, see "User Manual of LAN Control
Utility" contained in the CD-ROM.
AUTO POSITION button
When the image supplied from the computer is
displaced, carry out the following procedure.
1. Project a bright image containing as many texts
and characters as possible.
2. When the screen saver has been enabled, disable
it.
3. Press the AUTO POSITION button.
• The projector automatically makes optimum
positional settings for the input signal.
• When you press the AUTO POSITION button
while a signal from a video device (or signal
marked with *2 on page 46) is being input, a
window to select either of the following two
adjustment modes is displayed.
- AUTO ADJUST:
Suitable for signals supplied from a
computer.
- VIDEO SIGNAL:
Suitable for signals supplied from a video
device such as DVD. (When you select
this mode, the adjustment using the
RESOLUTION (MEMORIZE) menu (page 25)
becomes unavailable.)
Select an appropriate mode using the  or 
button and then press the ENTER button.
• If the projected image is still displaced even after
pressing the AUTO POSITION button several times,
refer to the procedure to adjust computer images.
(See pages 28 and 29.)
• When you carry out this procedure with a dark
image, the image may be displaced.
Volume from the speaker
Press the VOLUME  or  button to change the
volume from the speaker.
The volume control bar will appear on the screen.
• The volume control bar will disappear about 10
seconds after the VOLUME button is released.
• The VOLUME buttons don't function while the
menu is being displayed.
• When a high-level audio signal, such as a DVD
audio signal, is supplied to the AUDIO IN terminal,
the output from the speaker may be distorted.
EN-17
VOLUME 10