Section 4: Vent Information; Venting Termination Minimum Requirements - Quadra-Fire MTVERNON-AE-MBK Owner's Manual & Installation

Mt. Vernon Pellet Stove (AE)
4
Vent Information
A. Venting Termination Minimum Requirements
O
Figure 10.1
All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below.
A 12 in. Above Finish Grade (the grade surface
must be a non-combustible material
B 12 in. Open door or window: below or to the side
48 in. no OAK
B 12 in. Open door or window: above
C 6 in. Permanently closed window: above, below
or to the side
D 18 in. Vertical clearance to a ventilated soffit
36 in. no OAK located above the terminal within a hori-
zontal distance of 2 ft from the center-line
of the terminal
E 12 in. Clearance to unventilated soffit
F 12 in. Clearance to outside corner
G 12 in. Clearance to inside corner
H 36 in. Above gas meter/regulator measured from
horizontal center-line of regulator
I 36 in. USA Clearance to service regulator vent outlet
72 in. Canada
J 12 in. Clearance to non-mechanical air supply
48 in. no OAK inlet to the building or the combustions air
inlet to any other appliance
K 10 ft horizontal Clearance to mechanical air supply
3 ft vertical
L 7 ft. Above paved sidewalk, paved driveway
located on public property
M 12 in. Under an open veranda, porch, deck or
balcony
N See Note Electric service: above, below or to the
below* side (location must not obstruct or interfere
with access)
O 24 in. Adjacent building, fences and protruding
parts of the structure
P 12 in. Clearance above roof line for vertical
terminations
*NOTE: Consult local building, fire officials or authorities having jurisdic-
tion. Local codes or regulations may require different clearances.
Page 10
D
E
L
C
B
V FIXED
CLOSED
OPEN
F
V
B
V
Termination Cap
7034-106E
Inside Corner
G
V
A
H
FIXED
OPEN
V CLOSED
G
B
V
A
B
G
X Air Supply Inlet Gas Meter
24 in. Above grass, top of plants, wood or any other com-
bustible
12 in. Clearance from any forced air intake of other appli-
36 in. no OAK ance
12 in. Clearance horizontally from combustible wall
15 in. Vented directly through a wall, minimum length of
horizontal pipe
6 in. horizontal Minimum horizontal or vertical terminations must
12 in. vertical protrude from wall
OT
Do NOT Terminate Vent:
• In any location that will allow flue gases or soot from enter-
ing or staining the building
• In any location which could create a nuisance or hazard
• In any enclosed or semi-enclosed area such as a carport,
garage, attic, crawl space, under a sun deck or porch,
narrow walkway
• Closely fenced area, or any location that can build up
a concentration of fumes such as a stairwell, covered
breezeway, etc.
OT
Termination must exhaust above air inlet elevation.
• It is recommended that at least 60 inches (1524mm) of
vertical pipe be installed when appliance is vented directly
through a wall. This will create a natural draft, which will
help prevent the possibility of smoke or odor venting into
the home during a power outage.
• It will also keep exhaust from causing a nuisance or hazard
by exposing people or shrubs to high temperatures.
• The safest and preferred venting method is to extend the
vent vertically through the roof or above the roof.
V
N
N
N
Electrical
V V
Service
N
V
P
M
I
V X
J or K
Restricted Area
September 1, 2008
R