Table of Contents
Advertisement
Normal Playback
Preparation:
• Turn on the TV.
• Tune the TV to the DVD/VCR
Receiver output channel (OH
3 or 4) or set the TV's source selector to VIDEO.
• If a direct VIDEO/AUDIO
connection is made between the
DVD/VCR Receiver and the TV, set the TV's source selector
to VIDEO.
• Set the Output Source to VCR as shown in 'Selecting
the
Input/Output
Source" on page 15.
Insert
a prerecorded
video
cassette.
The O'--Q indicator witt light and the DVD/VCR
Receiver
will power-up automatically.
• Make sure that the Q
indicator in the display
window is not lighted. If it is, press POWER once.
• If a tape without a safety tab is inserted, the unit wilI
start playback automatically.
Press
PLAY once.
PLAY appears
on the TV screen.
• It is not necessary to select the tape speed for
playback. It will be automatically
selected by the
DVD/VCR Receiver.
• In playback, the TV/VCR selector switches to VCR
mode automatically.
Press
STOP
to stop playback.
STOP
appears
on the TV screen.
• If the tape reaches the end before STOP is pressed, the
DVD/VCR Receiver will automatically
stop, rewind and
eject the tape, and it will turn itself off.
Tracking
Control
Auto Tracking
The automatic
tracking
function
adjusts
the picture
to
remove
snow or streaks.
The AUTO
TRACKING
function
works
in the following
cases:
• A tape is played back for the first time.
• Tape speed (SP, SLP) changes.
• Streaks or snow appear because of scratches on the tape.
Manual
Tracking
if noise appears
on the screen
during
playback,
press
either
CH/TRK
_
on the remote
control
or CH/PRE-
SET (A/T)
on the front panel
until the noise on the
screen
is reduced.
• If vertical jitter is present, adjust tracking controls very
carefully.
• Tracking is automatically
reset to normal when the tape is
ejected or the power cord is unplugged for more than 3
seconds.
Special Effect Playbacks
_
Special
effects
playback
notes
• Horizontal
lines (noise bars) will appear on the TV screen.
This is normal.
• The audio is automatically
muted during special effect modes,
so there is no sound during search.
• During high-speed
picture search
mode, a short period is
needed to stabilize tape speed when re-entering
the PLAY
mode. Slight interference may be observed during this period.
Search
This function
lets you quickly
and visually
search
for a
desired
tape section
in either
direction:
forward
or
reverse.
1 Press
nEW
441 or FWD _
during
playback.
The
DVD/VCR
Receiver
will be activated
in the SEARCH
mode.
2 To return
to playback,
press
PLAY.
Still Picture and Frame-by-Frame
Playback
1 Press
PAUSE/STEP
during
playback.
Still picture
will appear
on the TV screen.
• If a stilI picture vibrates vertically, stabilize it using
CH/TRK(A/T)
on the remote control.
• If the DVD/VCR Receiver is left in the STILL mode for
more than 5 minutes, the DVDNCR
Receiver will auto-
maticatty enter the STOP mode to protect the tape and
video heads.
2 Press
PAUSE/STEP
repeatedly
to advance
the
video
picture
one frame
at a time while viewing
a still
picture.
3 To return
to playback,
press
PLAY.
Slow Motion
1 Press SLOW.
The tape will be played
back at a speed
1/19 times
slower
than the normal
speed.
• During slow playback, use CH/TRK (AtY) on the Remote
Control to minimize noise bands.
• If stow motion mode continues for more than 3 minutes,
the DVD/VCR Receiver wili automatically
change to play-
back mode.
2 To return
to playback,
press
PLAY.
Variable
playback
speed control
During
Playback
use 4/1_,
you can reach the follow-
ing playback
speeds.
(-7xplay
(REV),
-3xplay
(-3PLY),
-play (-PLAY),
still
(STILL),
1/19 slow (SLOW),
play (PLAY),
2xplay
(2PLY),
7xplay(OUE)).
During
slow motion
and shuttle,
the noise bars may
appear
on the picture
according
to the status of tape.
if distortions
can be seen in the picture,
reduce
them
with CH/TRK
(A/T)
on the remote
control.
Advertisement
Table of Contents
Troubleshooting
