Incline Rail & Console Mast; Handlebar - SOLE E35 Owner's Manual

INCLINE &CONSOLE
See Page 10 for illustration
1. Install the Incline Rail Assembly (2) into the U-channel bracket of the Main
Frame (1). Secure with the six bolts & associated hardware as follows: From
the sides install two Hex Head Bolts (107) with two Flat Washers (157) and
two Nylon Nuts (134). From the top install four Hex Head Bolts (108), four
Split Washers (158), four Flat Washers (157) and four Star Washers (151), as
shown in figure 1, and tighten with Wrenches (159 & 162).
2. Connect the 3 wire harness (48) to the female receiver cable coming from the
Incline rail assembly (2). Connect the Three pin position Sensor connector
(49) to the female receiver coming from the Incline rail assembly (2).
3. Locate the Console Mast (12) and Console Mast Cover (72) and slide the
Cover onto the Mast as far as it will go. Make sure the Console Mast Cover is
facing the correct way. At the top opening of the Main Frame of the elliptical
is a computer cable (50) Secure the free end of the twist tie that exits the
bottom of the console mast (12) to this cable. Pull the opposite end of this
twist tie up through the console mast (12) until the cable exits the top.
Install the Console Mast (12) into the receiving bracket on the top of the
Main Frame. Pull slightly on the computer cable at the top of the mast while
installing. This will ensure the cable does not get pinched and shorted during
console mast assembly.
4. Put one Split Washer (155) onto the Long Hex Head Bolt (101) and install
through the left side of the receiving bracket into the Console Mast (12). Put
the two Curved Washers (156) onto the two Short Hex Head Bolts (106) and
install through the front of the console mast.. Using Wrench (159), tighten
the the (106) bolts first, then the (101) bolt, and lastly the fourth bolt, which
is pre-installed, firmly. These bolts should be tightened as much as you pos-
sibly can. This is the main joint of the unit. If not tightened sufficiently, this
could lead to noise and instability issues.
5. Plug all of the connectors into the back of the console: Computer Cable (50),
Two Hand Pulse cables (35), Incline switch cable (40), and Resistance switch
cable (39). Secure the Console (45) on the console mounting plate with four
MSxlOmm Phillips Head Screws (117). Note:
there will be
anempty
four
pin port on
the back of the console. This model doesn't use this port.
#142.3/8"x 19x 1.5T
Flat Washer (2 pcs)
#157.5/16"x 20 x 1.ST
Flat Washer (4 pcs)
#156. 3/8"x 23 x 2T
Curved Washer (2 pcs)
#155.3/8"x 2T
Split Washer (1 pcs)
#117. M5 x lOmm
Flat Washer (4 pcs)
#134. 3/8"x 7T
Nylon Nut (2 pcs)
#158. 5/16"x 1.5T
Split Washer (4 pcs)
#151.5/16"
Star Washer (4 pcs)
#106. 3/8"x 3/4"
Hex Head Bolt (2 pcs)
#108.5/16"x 2-1/4"
Hex Head Bolt (4 pcs)
#107.3/8"x 1-1/2"
Hex Head Bolt (2 pcs)
#101.3/8"x 2-1/4"
Hex Head Bolt (1 pcs)
HANDLE
See Page 10 for illustration
1. Install two Wave Washers (153) onto the Left and Right sides of the Handle
Bar axles.
2. Slide the Left (1 O) and Right (11) Handle Bars onto the appropriate side of
the axle.The handlebars have a small sticker on them indicating L (left) and R
(right). Make sure the handlebars are facing the correct direction - see
illustration
3. Place two Flat Washers (145) onto the two Hex Head Bolts (100) and attach
and tighten in the threaded holes at the end of the axles.
4. Install the Front Handle Bar Covers (83 & 84 right side; 85 & 86 left side) over
the Handle Bar axle connections with the six screws (126).
#153.17rnm
Wave Washer (2 pcs)
#145.5/16"x 23 x 1.ST
Flat Washer (2 pcs)
#126. 3.5 x 12mm Sheet
Metal Screw (6 pcs)
#100. 5/16"x 15rnm
Hex Head Bolt (2 pcs)
#21. Bracket (2 pcs)
E25 / E35 ELLIPTICAL 8