Baking Tips; Roasting Tips - Magic Chef 9512WUA Owner's Manual

Baking Tips
Use a reliable recipe and accurately measure fresh
ingredients. Carefully follow directions for oven
temperature and cooking time. Preheat oven if
recommended.
Use ,the correct rack position. Baking results may be
affected if the wrong rack is used.
* Top browning may be darker if food is located toward
the top of the oven. '
* Bottom browning may be darker if food is located
toward the bottom of the oven.
* When using two racks for baking, allow enough space
between the racks for proper air circulation. Browning
and cooking results will be affected if air flow is blocked.
Cookware material plays an important part in baking
results. Always use the type and size of pan called for in the
recipe. Cooking times or cooking results may be affected if
the wrong size is used.
* Shiny metal pan reflects heat away from the food,
produces lighter browning and a softer crust. Use shiny
pans for baking cakes or cookies.
Dark metal pan or a pan with an anodized (dull)
bottom absorbs heat, produces darker browning and a
crisper crust. Use this type of pan for pies, pie crusts or
bread.
* For optimum baking results, bake cookies and biscuits
on a flat cookie sheet. If the pan has sides, such as a
jelly roll pan, browning may not be even.
* If using heatproof glassware, or dark pans such as
Baker's Secret reduce the oven temperature by 25°F
except when baking pies or bread. Use the same baking
time as called for in the recipe.
Allow hot air to flow freely through the oven for optimum
baking results Improper placement of pans in the oven will
block air flow and may result in uneven browning. For
optimum browning and even cooking results:
* Do not crowd a rack with pans. Never place more than
one cookie sheet, one 13x9x2-inch cake pan or two
9-inch round cake pans on one rack.
Stagger pans when baking on two racks so one pan is
not directly over another pan.
* Allow two inches between the pans or between the pan
and the oven walls or door.
Check the cooking progress at the minimum time
recommended in the recipe. If necessary, continue checking
at intervals until the food is done. If the oven door is opened
too frequently, heat will escape the oven; this can affect
baking results and wastes energy
If you add additional ingredients, use different pans, or
alter the recipe, expect cooking times to increase or
decrease slightly
Roasting Tips
Roasting isthe method for cooking large, tender cuts of meat
uncovered, without adding moisture. Most meats are
roasted at 325°F. It is not necessary to preheat the oven.
Place the roasting pan on either of the two lowest rack
positions.
Use tender cuts of meat weighing three pounds or more.
Some good choices are: Beef rib, ribeye, top round, high
quality tip and rump roast, pork loin roast, leg of lamb, veal
shoulder roast and cured or smoked hams.
Season meat, if desired, either before or after roasting. Rub
into the surface of the roast if added before cooking.
Place the meat fat-side-up on a rack in a shallow roasting
pan Placing the meat on a rack holds it out of the drippings,
thus allowing better heat circulationfor even cooking As the
fat on top of the roast metts, the meat is basted naturally,
eliminating the need for additional basting.
The cooking time is determined by the weight of the meat
and the desired doneness. For more accurate results, use
a meat thermometer. Insert it so the tip is in the center of the
thickest part of the meat. It should not touch fat or bone.
Remove the roast from the oven when the thermometer
registers approximately 5°F below the desired degree of
doneness. As the meat stands, the temperature will rise.
NOTE: For more information on cooking meat and
poultry, contact the USDA Meat & Poultry Hotline at
1-800-535-4555.