Installing The Tubing; Instalaci6N De La Tuberia - GE GX1S50F Owner's Manual And Installation Instructions

Table of Contents

Advertisement

Installation Instructions.
Instdling the Tubing
1. Measure 3/4_< from the end of each remaining piece of tubing (faucet
end and inlet end) and mark with a pencil (Fig.6).(Checkfor roundness,
smoothness, cuts, nicks,flat spots and sharp edges. It mug be
necessarg to recut the tubing.)
3/4"
19ram
INCORRECT
Fig. 6
2. Observe arrows on top of manifold that indicate inlet and outlet. Failure
to follow will result in water leaks when filter canister is removed.
3.
Pushthe tubing firmlg into each fitting on the manifold until the line is
flush with the fitting collar. (Ifthe tubing is removed, re-cut the end,
measure, mark and re-insert).Tubing must be fullg inserted to avoid
leaks (Fig.7). (To remove tubing: Depress and hold white caller; pull
tubing out to remove.)
WhiteCollet
(DO NOT REMOVE)
Insertion lille_i_--
3,/4 "--_'l
Insert t ubing _
__y
#FT
b
Engagement
J_l
4"(3/8" tubing) I
Fig. 7
4. Pullout slightlg on tubing to ensure a good seal.
5. Install the other end of the tubing from the inlet side of the manifold to
the feed water adapter.
NOTE: Inspect the ends of the tubing to be sure there are no
imperfections and that the end of the tubing is cut square. It mug be
necessarg to cut the tubing again.
instrucciones
de instalaci6n.
C6mo instalar la tuberia
1.
Midauna distancia
de 3/4 pulgada desdeel extremo de cada pieza
restante
de tuberia (extremo d el grifo g extremo de la entrada) g marque
conkipiz (Fig.
6). ( Revise quequede pareja,
lisa g queno tenga cortes,
hendiduras,
puntos planos o bordes filosos.
Esposible quesenecesite
volver a cortar la tuberia.)
INCORRECTO
Fig. 6
2.
3.
Observe lasflechas en la parte superior del recolector que indican
la entrada g la salida. Noseguir las indicaciones resultar@en fugas
cuando se retire el cartucho del filtro.
Empuje latuberia firmemente hacia cada conexi6n en el recolector
hasta que latuberia est@ nivelado con elcollar. (Sise retira latuberia,
vuelva a cortar el extremo, mida, marque g vuelva a insertar).Latuberia
debe estar firmemente insertada para evitar fugas (Fig.7).fPeru rotifer
Io tuberio: Libere y sostengo Io boquillo blonco; hole Io tuberio hocio
fuera para retirarJ
Boqu,,,.
h,.nc.
(NO RETIRAR)
__
Linea deinserci6n -----_II_--- 3,/4"-------_ I
Insertartuberia
_
__
Enganche I
3/4"
--_
(tuberia d e3/8") I
Fig. 7
4. Saque la tuberia ligeramente para asegurar un buen sellamiento.
5. Instale el otro extremo de la tuberia desde el lado de la entrada del
recolector al adaptador de suministro de agua.
NOTA: Inspeccione los extremos de la tuberia para asegurarse que no
hoga imperfecciones g que el extremo de la tuberia se haga cortado
perpendicularmente.
Esposible que se necesite volver a cortar
la tuberia.
JO

Advertisement

Table of Contents
loading

Table of Contents