System Installation; Instalaci6N Del Sistema - GE GX1S50F Owner's Manual And Installation Instructions

Table of Contents

Advertisement

Installation Instructions.
Mounting System Installation
Pick a location under the sink to mount the sgstem. Location should be
easilU accessiblewith at least Sinches of clearance between the bottom of
the filter canister and the floor or bottom of the cabinet; any lesswill result
in difficuitg of removing filter canister, Allow enough space on either side of
the sgstem for the tubing connections.
A. PREFERREDINSTALLATION
(Mounting Using the Screw Provided [Fig. 4])
1. Remove shrink wrap from filter sgstem.
2. Sgstem should be mounted to a stud in the wall or solid firm surface.
3. Usethe screw (B)provided to mount through the screw hole in the
center of the manifold (A),(Pre-drilla 1/16" pilot hole, if needed),
NOTE:If mounting to drgwall, with no stud, a drgwall anchor (not
included)must be used.
(B) Screw
(A) Manifold
Fig. 4
B. OPTIONAL INSTALLATION
(Mounting Using the Mounting Tape Provided [Fig. S])
(If mounting to drywall, the screw must be used also).
1. Remove shrink wrap from filter system.
2. Clean wall surface to remove ang dirt, oil or grease and drg thoroughlg.
3. Using the double-sided mounting tape provided (C),remove one side of
the protective wax paper and apply the entire piece to the back side of
the manifold (A),applying firm pressure to the entire piece.
4. Remove the remaining wax paper from the double-sided mounting
tape (C)and adhere it to the cleaned wall surface, applying firm
pressure to the entire piece.
(C) Mounting tape
(A)Manifold
Fig. 5
instrucciones de instalaci6n.
Montaje del sistema
Seleccione una ubicaci6n debajo del lavaplatos para instalar el sistema. La
ubicaci6n debe ser de f6cil acceso, al menos con Spulgadas de espacio
entre la base del cartucho del filtro g el piso o la base del gabinete;
cualquier espacio inferior presentar6 dificultades para retirar el cartucho
del filtro. Permita suficiente espacio para cualquier lado del sistema para
las conexiones de la tuberia.
A. INSTALACION PREFERIDA
(Nontaje utilizando el tomillo suministrado [Fig. 4])
Retirela envoltura del sistema del filtro.
1,
z
3.
El sistema debe estar instalado en una tachuela en la pared o
superficie s61ida.
Utilice el tornillo (B)suministrado para instalar a trav@sdel orificio del
tornillo en el centro del recolector (A). ( Preperforeun orificio piloto de
1/16", de ser necesario).
NOTA:Si se instala en pared de 9eso, sin tachuela, se debe usar un ancla
de pared de yeso (no incluida).
(B)Tornillo
(A)Recolector
Fig. 4
B. INSTALACION
OPCIONAL
(Montaje
utilizando
la cinta de montaje
suministrada
[Fig. 51)
(Si la instalaci6n
es en una pared de geso [drywall],
tambign se debe usar
el tornillo).
1. Retire la envoltura del sistema del filtro.
2. Limpiela superficie de la paredpara retirarcualquiersuciedad, a ceite
o grasag sequecompletamente.
3. Conla cinta de dobleadhesivo para montajequesesuministra (c),retire
un lado del papelceraprotectorg apliquea toda la piezaen la parte
posteriordelrecolector(A), haciendopresi6nfirme a toda la pieza.
4. Retire el papelcera restantede la cinta de dobleadhesivo(C) g p@guela
a la superficielimpiade la pared,aplicandopresi6nfirme a toda
la pieza.
(C) Cinta para montaje
(A)Recolector
Fig. 5
9

Advertisement

Table of Contents
loading

Table of Contents