Table of Contents
Advertisement
Quick Links
Models GNUT05Z, GXUT05Z, GNUV10Z, GXUV10Z, GNUL30Z,
TABLE OF CONTENTS:
IMPORTANT INSTALLATION RECOMMENDATIONS
Read entire manual. Failure to follow all guides and rules could cause personal injury or property damage.
• Check with your local public works department for plumbing codes. You must follow their guides as you install the Water Filtration
system.
• Use the Water Filtration system on a potable, safe-to-drink, home COLD water supply only. The filter cartridges will not purify water
or make unsafe water safe to drink. DO NOT use on HOT water (100°F. max).
• Protect the Water Filtration system and piping from freezing. Water freezing in the system will break it.
• Your Water Filtration system will withstand up to 125 psi water pressure. If your house water supply pressure is higher than 100 psi
during the day (it may reach higher levels at night), install a pressure reducing valve before the system.
WARNING: Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before
or after the system. GNUL30Z and GXUL30Z are certified for cyst reduction and may be used on disinfected water that may
contain filterable cysts. The water should be tested periodically to verify that the system is performing satisfactorily.
Small parts remaining after the installation could be a choke hazard. Discard safely.
7178977 (10-97) 215C1001P003-2
Pub. No. 49-5809-2
GE SmartWater
Water Filtration System
INSTALLATION INSTRUCTIONS
GXUL30Z & GXEM01Z
GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225
Ô
Page #
1
2
3
4
5
5
5
5
6, 7
For Use and Care questions call: GE Answer Center® 800.626.2000
1
NSF
®
GNUT05Z, GXUT05Z, GNUV10Z,
GXUV10Z, GNUL30Z, and GXUL30Z are
tested and certified to ANSI/NSF Standard
42 for particulate reduction Class I,
chlorine reduction Class I and taste and
odor reduction.
GNUV10Z and GXUV10Z are tested and
certified to ANSI/NSF Standard 53 for
volatile organic chemical reduction.
GNUL30Z and GXUL30Z are tested and
certified to ANSI/NSF Standard 53 for cyst,
turbidity and lead reduction.
Advertisement
Table of Contents
Related Manuals for GE SmartWater GNUT05Z
Summary of Contents for GE SmartWater GNUT05Z
-
Page 1: Table Of Contents
The water should be tested periodically to verify that the system is performing satisfactorily. Small parts remaining after the installation could be a choke hazard. Discard safely. 7178977 (10-97) 215C1001P003-2 For Use and Care questions call: GE Answer Center® 800.626.2000 Pub. No. 49-5809-2 GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225... -
Page 2: Tools And Materials Required For Installation
TOOLS AND MATERIALS REQUIRED FOR INSTALLATION • Slotted and Phillips screw drivers • Pliers and adjustable jaw wrench • Hand or battery powered drill and 1 ⁄4 ² bit (saddle valve installation) • Electric drill and a drill bit to drill a 1 ⁄4² hole (type as required) if a mounting hole is needed for the faucet CAUTION: To avoid damaging the sink, consult a qualified plumber or installer for drilling procedures. -
Page 3: Step-By-Step Installation Instructions
STEP-BY-STEP INSTALLATION INSTRUCTIONS FEED WATER SUPPLY Check and comply with local plumbing codes as you plan, then install a cold feed water supply fitting. For new home installation using standard plumbing fittings, see Fig. 2A below. A typical installation for existing homes using the saddle valve is shown in Fig. 2B below. Fig. -
Page 4: Electronic Faucet Installation
ELECTRONIC FAUCET INSTALLATION Nut (2) Fig. 3A. Fig. 3B. Be sure there is room underneath the sink to make the needed TOP VIEW connections. Select one of the following places to install the faucet: Screw (2) Screw (2) —IN an existing sink spray attachment or soap dispenser hole —IN a hole to be drilled in the sink top Faucet —IN a hole to be drilled in the countertop, next to the sink... -
Page 5: Wall Mounting
Tubing MOUNTING BRACKET TO CABINET WALL Fig. 4 7-9⁄16² connector The bracket can be used as a template for marking the location of the mounting screws. When determining the location of the bracket make sure you leave 1-1⁄2² to 2² of free area under the sumps to allow for sump removal and enough space on either side to make the tubing connections. - Page 7 GENERAL ELECTRIC PARTS CATALOG G G G G G G G N N N X X X X U U U E U U U L T V M L T V 3 0 1 0 3 0 1 0 5 0 1 0 5 0 Z Z Z Z Z Z Z 0 0 0 0 0 0 0 1 1 1 1 1 1 1...