Download  Print this page

Anti-Tip Bracket - KitchenAid GAS RANGE Installation Instructions Manual

30" freestanding gas range with standard clean oven
Hide thumbs

Advertisement

Important: Observe all governing codes
and ordinances.
This installation
must conform with
all local
codes and ordinances. In the absence of local
codes, installation
must conform with American
National Standard, National Fuel Gas Code ANSI
2223.1 - latest edition**.
Proper installation
is your responsibility.
A
qualified technician must install this range. Make
sure you have everything necessary for correct
installation. It is the installer's responsibility
to
comply with installation clearances specified on
the gas information
label. The gas information
label and model/serial rating plate are located on
the frame behind the broiler door.
Check location where range will be installed. The
range should be located away from strong draft
areas, such as windows, doors and strong
heating vents or fans. The range should be
located for convenient use in kitchen.
ALL OPENINGS IN THE WALL OR FLOOR WHERE
RANGE IS TO BE INSTALLED MUST BE SEALED.
Cabinet opening dimensions shown must be
used. Given dimensions are minimum
clearances.
Grounded electrical outlet is required. See
"Electrical requirements,"
Page 2.
Proper gas supply connection must be available.
See "Gas supply requirements,"
Page 2.
24-13116"
3
i
42-i14"
overall
height
36"
cooktop
height
I
WARNING: If the information in
this manual is not followed
exactly, a fire or explosion may
result causing property damage,
personal injury or death.
- Do Not store or use gasoline,
or other flammable vapors and
liquids in the vicinity of this or any
other aooliance.
ia"
min.
-WHAT id DO IFYOU SMELL GAS:
l
Do Not try to light any appliance.
l
Do Not touch any electrical
switch; Do Not use any phone in
your building.
l
Immediately call your gas supplier
from a neighbor's phone. Follow
gas supplier's instructions.
l
If you cannot reach your gas
supplier, call the fire department.
- Installation and service must be
done by a qualified installer,
service agency or the gas supplier.
Do Not pinch the power
supply cord between the
range and the wall.
Do Not seal the range to
the side cabinets.
If cabinet depth is greater
than 24", oven frame must
extend beyond cabinet
fronts by l/2" min.
Contact a qualified
floor covering
installer to check
that the floor
covering can
withstand
at least
9O'F above room
temperature.
Use an insulated
pad or l/4" plywood
under range if
installing range over
carpeting.
Shaded area
recommended
for installation
-1 --- -I--
1
***Note:
30" min. when bottom of wood
or metal cabinet is protected by not
less than l/4" flame retardant mill-
board covered with not less than
No 28 MSG sheet steel, 0.015"
stainless steel, 0.024" aluminum or
0.020" copper.
36" min. clearance between the top of
the cooking platform and the bottom
of an unprotected
wood or metal
Electrical Shock Hazard
It is the customer's responsibility
to contact a
qualified electrical installer and to make sure
that the electrical installation
is adequate and
make sure the electrical installation follows
the National Electrical Code, ANSUNFPA 70 -
latest edition*, and all local codes and
ordinances.
Take special care when cutting holes in wall or
floor. Electrical wires may be behind the wall
or floor covering and cause electrical shock if
you touch them.
Locate any electrical circuits that could be
affected by the installation of this product and
disconnect power circuit.
Failure to follow these instructions
could
result in death or serious injury.
Fire Hazard
Do Not obstruct the flow of combustion or
ventilation air.
Failure to follow this instruction
could result in
a fire.
Injury Hazard
To eliminate the risk of burns or fire, avoid
installing cabinet storage above the cooking
surface. If cabinets are already installed,
reduce the hazard of reaching over a heated
cooking surface by installing a range hood.
The range hood should extend a minimum of
5 inches out from the bottom front of the
cabinets.
Reaching over a heated cooking surface could
result in a serious burn or other injury.
Anti-tip bracket
-
The floor-mou&
anti-tip bracket MUST be installed. To
install the anti-tip bracket supplied, see Pages 3-4 and the
anti-tip bracket templatelinstruction
sheet.
Mobile home installation
The installation of this range must conform with
the Manufactured Home Construction and Safety
2 plastic
anchors
Standard, Title 24 CFR, Part 3280 [formerly the
Federal Standard for Mobile Home Construction
and Safety, Title 24, HUD (Part 28011 or, when
such standard is not applicable, the Standard for
Manufactured Home Installations, ANSI A225.1
and Manufactured Home Installations, Sites, and
Communities ANSI/NFPA 501A, or with local
codes.
When this range is installed in a mobile home, it
i
must be secured to the floor during transit. Any
floor-m01 unted
method of securing the range is adequate as long
anti-tip bracket
0
L
2 screws
(#10x l-1/2")
Not shown:
- literature pack
* orifice spuds
as it conforms to the standards listed above.
Bracket must be securely mounted to sub-floor.
Copies of the standards
listed may be obtained
from:
* National
Fire Protection
Association
Batterymarch
Park
Thickness of flooring may require longer screws
to anchor bracket to sub-floor. Longer screws are
available from your local hardware store.
Quincj,
Massachusetts
02269
** American
Gas Association
1515 Wilson
Boulevard
Arlington,
Virginia
22209
'age
1

Advertisement

loading

  Also See for KitchenAid GAS RANGE

  Related Manuals for KitchenAid GAS RANGE