Table of Contents
Advertisement
T7300F SERIES 2000 COMMERCIAL MICROELECTRONIC CONVENTIONAL OR HEAT PUMP THERMOSTAT
Installer Setup
Number
(Press
Unoccupied
Temp Key to
Select
change)
Temperature
37
display
adjustment.
Minimum off-
38
times in
heating.
Not used
39
Installer Setup
40
lockout
(keypad
lockout is
enabled and
disabled by dip
switch 1 on
back of
thermostat).
a
Number 2 must be set to 1 to extend fan operation.
Number 22 must be set to 1 and remote sensor(s) must be installed.
b
IMPORTANT
Review the settings to confirm that they match
the system. Press Run Program to exit the
Installer Setup. Be sure to set the current day
and time immediately.
Set Current Day and Time
1. Press Set Current Day/Time.
NOTE: On initial power up or after an extended
power loss, 1:00 pm flashes on the LCD
until a key is pressed.
Set Current
Day/Time
Set Program
Run
Occupied
Unoccupied
Program
Start Time
Start Time
Day
Temporary
Set Current
Clear
Occupied
Day/Time
Start Time
Copy
Continous
Unoccupied
2. Press Day until the current day is displayed.
62-0125—3
Table 2. Thermostat Installer Setup Options (Continued)
Factory Setting
Display
0
No difference in
displayed temperature
and actual room
temperature.
4
4—4-minute minimum
off-time.
—
—
0
0—No Installer Setup
lockout.
Set Day/Time
PM
Set Temperature
Change
Time/Temp
Occupied
Unoccupied
Mon
Temp
Temp
Heat/Cool
Settings
System
Fan
Description
Display
1 thru 6 1—Display adjusts to 1°F
0, 1, 2,
3, or 5
—
1
NOTE: Sun=Sunday, Mon=Monday, Tue=Tues-
Day
3. Press increase
time is displayed.
NOTE: Tapping the Set Current Day/Time will
M4951C
4. Press Run Program.
Run
Program
6
Other Choices
(Press
or
key to change)
Description
(0.6°C) higher than actual
room temperature.
2—Display adjusts to 2°F
(1.1°C) higher than actual
room temperature.
3—Display adjusts to 3°F
(1.7°C) higher than actual
room temperature.
4—Display adjusts to 1°F
(0.6°C) lower than actual
room temperature.
5—Display adjusts to 2°F
(1.1°C) lower than actual
room temperature.
6—Display adjusts to 3°F
(1.7°C) lower than actual
room temperature.
Minimum number of
minutes (0 thru 5) the
heating equipment will be
off between calls for heat.
—
1—Installer Setup lockout
activated.
day, Wed=Wednesday, Thu=Thursday,
Fri=Friday, Sat=Saturday.
Set Program
Set Temperature
Change
Time/Temp
Run
Occupied
Unoccupied
Occupied
Unoccupied
Program
Start Time
Start Time
Day
Temp
Temp
Tue
Temporary
Set Current
Clear
Heat/Cool
Occupied
Day/Time
Start Time
Copy
Settings
Continous
Unoccupied
System
Fan
or decrease
change the time in one hour increments.
Set Program
Set Temperature
Change
Time/Temp
Run
Occupied
Unoccupied
Occupied
Unoccupied
Program
Start Time
Start Time
Day
Temp
Temp
Tue
Temporary
Set Current
Clear
Heat/Cool
Occupied
Day/Time
Start Time
Copy
Settings
Continous
Unoccupied
System
Fan
Set Program
Set Temperature
Change
Time/Temp
Run
Occupied
Unoccupied
Occupied
Unoccupied
Program
Start Time
Start Time
Day
Temp
Temp
Mon
Occupied 1
Temporary
Set Current
Clear
Heat/Cool
Occupied
Day/Time
Start Time
Copy
Settings
System
Continous
Unoccupied
System
Fan
Heat
Actual
Setting
—
Set Day/Time
PM
M4952C
until the current
Set Day/Time
PM
M4953C
AM
Room
Fan
Auto
M4954B
Advertisement
Table of Contents
