Zenith SY3588 Operating Manual & Warranty page 32

Z-TRAK TRACKBALL REMOTE CONTROL
I)ROGRAMMING YOUR Z-TRAK TRACKBALL REMOTE
The Zenith Trackball remote is already programmed
ta work with most Zenith VCRs. If your VCR is not
a Zenith, or if your Zenith VCR does not respond to
the trackball remote, you will need to program your
remote as follows:
1. Refer to lhe VCR Codes by Brand Name Listing ta-
ble on the next page. Locate the 3-digit number
which corresponds to your brand of VCR.
2. Make sure the TV is On.
2;. While pointing the Zenith Z-Trak remote towards
your TV, simultaneously hold the MUTE and EN-
TER keys until the TV displays a "VCR Setup"
menu screen (takes about 3 seconds). The VCR key
will ligh! upon entering 1:he Programming Mode.
4. Notice that the current VCR brand code (initially
20t) is displayed on the screen. Roll the trackball
up or down (or use Chan Up/Down) to choose the 3-
digit number of your VCR.
5. When (he correct 3-digit number is displayed on the
TV screen, press the POWER key to see if your
VCR turns On and Off properly. If the VCR does
not respond, refer to the VCR Code Brand Listing
table to select a different 3-digit number.
6. If your VCR turns On and Off successfully, press
the trackball (or ENTER) to save the current VCR
brand code. The VCR Setup screen will disappear
from the TV. Also tile VCR key will blink 3 times
upon exiting the Programming Mode. The remote
will be in the VCR mode.
7. Now try other controls on your VCR, such as PLAY,
REWIND, etc., to make _ure that the correct VCR
brand code number was selected. (If not, repeat
steps 1 to 7.)
8. The MUTE key can he pressed at any time to cancel
programming mode.
9. Note: Only the VCR Mode can he programmed.
Pressing the VCR or TV mode key will have no ef-
fect in the Programming Mode. Similarly VOL
Up/Down RECRD, and FLSHBK will have no func-
tion in the Programming Mode.
10. The remote will exit Programming Mode automat-
ically after 60 seconds if no key or trackball move-
ment is detected.
.AUTO FIND: PROGRAMMING YOUR Z-TRAK REMOTE TO CONTROL VCR
i[f you have tried all 3-digit codes listed for your VCR manufacturer, and none of them operate your VCR, you will need to try
"AutoFind" to see if a different code will operate your VCR. Proceed as follows:
1. Make sure your VCR and TV are turned on.
2. Simultaneously hold the MUTE and ENTER keys
until the VCR key lights up (about three seconds).
13. Point the: Z-Trak trackball remote towards your
VCR. Press CHAN (Up) followed by POWER. If
your VCR did not turn off, keep repeatedly pressing
CHAN (Up) followed by POWER until the VCR re-
sponds,.
4. If your VCR turned off, press ENTER to save the
code. (Write it down for future reference.) The VCR
key will flash three times after ENTER is pressed.
5. Now try other controls on your VCR, such as Play,
Rewind, etc., to make sure that the correct VCR
brand cede number was selected. (If not, repeat
steps 2 to 4,)
6. The MUTE key can be pressed at any time to cancel
AutoFind mode. The original VCR brand code will
remain unchanged.
7. The remote will exit AutoFind mode automatically
after 60 seconds, if no key press or trackball move-
ment is ,detected,
m_,,aT, _:::,, -
Point at VCR
I
3(t63-O 12 _ 3