Table of Contents
Advertisement
GET
TO KNOW
THE REMOTE
CONTROL:
MBR
3457
PROGRAMMING
YOUR
REMOTE
If yt,u are using Zenith products, the remote is programmed for the most commonly used codes. For other audio/video brands you
will have to program the remote.
Follow these steps for each product you are using:
NOTES:
To program
the remote:
1. Locate the three-digit code for your brand (such as Zenith) and
equipment (such as VCR) in the code table.
2. Press and hold PRG with a small blunt object until the indicator
lights (about three seconds).
3. Press TV, VCR, CABLE
or AUX to select the product
you
want your remote
to control.
(Use CABLE or AUX to
program
your remote for a second
TV or VCR or to
program
your remote
for a video disc player or audio
equipment.)
4.
Enter the three-digit code then press ENTER. The indicator light
should flash then turn offto indicate that the code was accepted. If
the light stays on, repeat steps 3 and 4 or try using a different code.
5. Write the codes that operate
your equipment
on the label
inside the battery
compartment
for future reference.
UI To erase all code programming and return to the factory
preset codes, enter code 9-1-1 when programming the
remote.
If no key on your remote is pressed within 60 seconds, the
programming process will stop, and you will have to start
again.
I:::1 You may cancel programming at any time by pressing PRG.
SPECIAL
FEATURES
AUX+I, AUX+2, AUX+3 CAPABILITY
Your remote can control up to seven electronic components, if
you have programmed the remote for four components using the
TV, VCR, CABLE and AUX keys, you may also program it for
up to three additional components.
To program
AUX+I,
AUX+2,
& AUX+3:
1. Locate the three-digit code for your equipment in the code table.
2. Press and hold PRG until the indicator lights.
3. Press AUX and "'1" simultaneously
to select AUX+I.
4. Enter the three-digit code then press ENTER. The indicator light
should flash then turn off to indicate that the code was accepted. If
the light stays on, repeat steps 3 and 4 or try using a different code.
5. Repeat steps 2 -- 4 for AUX+2 and AUX+3 programming.
6.
Write the codes that operate
your equipment
on the label
;
inside the battery
compartment
for future reference.
Once programmed,
hold down the AUX key and press 1, 2 or 3,
to access the additional AUX +1, 2 or 3 mode.
CABLE BOX VOLUME
You may use your remote to control cable box volume and mut-
ing if available on your equipment.
I12
To program the cable box volume:
I
Programyour cable box code into the CABLE or the AUX
mode. I'
i Repeat the pn_gramming steps, again using the CABLE or AUX I
key. hutenter code 3-9-.-9inste',dof a brand c_xleand press
I
ENTER.
!
NOTE:
F..l To restore TV volume/mute control to the CABLE or AUX
mode, reprogram your cable code into that mode.
AMPLIFIER
VOLUME OVERRIDE
You may use your remote to override your TV, VCR or video
disk player's volume functions with your amplifier's volume and
muting.
To program
the amplifier
volume
override:
1. Program your amplifier code into the CABLE or one of the
AUX modes.
2. Select the mode on your remote O'V, VCR, etc.) where you
want the amplifier
volume control function to appear.
In other
words, if you want to operate the volume and mute of your
amplifier while the remote is in TV mode, press TV for this step.
3. Enter code 4-9-9,
followed by ENTER.
The amplifier volume and mute features are now available in the
TV mode.
NOTES:
I.J To restore normal volume and muting control to your TV
cable box, reprogram the remote for these units into each
mode (TV, VCR, etc.) to be restored.
I::l CD and tape devices will automatically select amplifier vol-
ume and mute.
........
3_4
Advertisement
Table of Contents
