Table of Contents
Advertisement
UNIVERSAL
REMOTE
CONTROL
PROGRAMMING
YOUR
REMOTE
If you are using Inteq products,
the remote
is programmed
for
the most commonly
used codes. For other brands -- or if your
remote fails to control your Inteq products
-- you will have to
progrmn
the remote.
Follow these steps t'or each product
you are using:
1. Look
up the three-digit
code for your brand
(such
as
Zenith)
and type of equipment
(such
as VCR)
in the
code table
on the following
page.
2. Press
and hold PRG
with
a small
blunt
object
until
the indicator
lights
(about
three
seconds).
3. Press
TV, VCR,
CABLE,
or AUX
to select
the
product
you want
your remote
to control.
(Use
CABLE
or AUX,
to program
your remote
for a
sec, ond TV or VCR
or to program
your remote
for a
video
disc player
or audio
equipment.)
4. Key ir_ the three-digit
code
for your equipment,
then
press
ENTER/TUNE.
The indicator
light should
flash, 1:hen turn off to indicate
tl_at the code was
accepted.
If the indicator
stays c,n, repeat
step:s 3 and 4
or try using
a different
code.
5. Write
the codes
that operate
yc,ur equipment
on the
label
inside
the battery
compartment
for future
reference.
To erase all code programming
and return to the factory preset
codes, key in code 9--1-1 when programming
the remote.
NOTES:
Ca The remote cannot be prograrnmecl while in the StarSight
mode: Choose TV, VCR, CABLE or AUX mode bef'ore
pressing PRG.
[] If no key on your remote is pressed within 60 seconds, the
programming process will stop, and you will haw_ to start
again.
t_ You may cancel programming at any time by pressing
PRG.
SPECIAL
FEATURES
AUX+I,
AUX+2,
AUX+3
Capability
Your remote can control up to seven electronic
components.
If
you have programmed
the remote for four components
using
the TV, VCR, CABLE
and AUX keys, you may also program it
for up to three additional components (AUX+I,
AUX+2,
AUX+3)
by holding
the AUX key and pressing the 1, 2 or 3 key
during programming.
Once programmed,
hold down the AUX
key and press 1, 2 or 3, to access the additional
AUX +1, 2 or 3
mode.
Cable Box Volume
You may use your remote to control cable box volume and mut-
ing if available on your equipment.
First program your remote
with the brand code for your cable device using the CABLE
or
AUX key. Then repeat the programming
steps, again using the
CABLE
or AUX key, but key in code 3-9-9
instead of a brand
code.
To restore TV volume/mute
control to the CABLE
or AUX
mode, reprogram
your cable code into that mode.
Amplifier
Volume
Override
You may use your remote to override
your TV, VCR or video
disk player's volume functions with your amplifier's
volume and
muting.
1. Program
your amplifier
code
into the CABLE
mode
or one of the AUX
modes.
2. Select the mode on your reraote (TV, VCR, etc.)
where you want the amplifier
volume cont:ml
function to appear.
In other words, if you want to
operzte the w)lume and mute of your amplifier
while
the remote is in TV mode, press TV for thi.'; step.
3. Begin the programming
steps as described
in
"Programming
Yo__," Remote"
and enter code 4--9-9,
followed
by ENTER.
The amplifier volume and mute features are :aow
available in the current mode.
To restore normal volume
and muting control to your TV,
VCR, ca'31e or laser disc player, reprogram
the remote for these
units into each mode (TV, VCR, etc.) to be restored.
NOTE:
[] CD and tape devices will automatically
select amplifier
vol-
ume and mute.
29_o
4--4
Advertisement
Table of Contents
