Advertisement
install
Batteries
in the Remote
Is Remove the battery compartment cover on the back of the remote.
2. insert new batteries, Hatch the polarities (+ and -) on the batteries with the diagram on the remote,
3. Put the battery compartment cover back on the remote.
lmpor1:ant Ba1:tery Informal:ion
if you're not going 1:o use 1:he remo1:e for a mon1:h or more_ be sure 1:o remove
1:he hal:reties
because they can leak an_ cause _ma_e,
* Dispose of b_;_eries
in1:heproper manner, according 1:o federal, s1:a1:e,
and localregu|a1:ions.
, Anyba1:1:erymay_eake_ec1:roly1:eifmixedwi1:h
adifferen1:ba1:1:ery1:ype_if
inse_edin¢orren1:ly,
if a_Iba_1:eries
areno1:rep_ateda1:1:hesame1:ime_if
disposed of infire_ or ifan a_emp1: ismade I:o charge a ba%1:ery no1:in1:ended 1:o be recharged.
* Discard leaky ba1:1:eries immedia1:ely,
Leaking ba1:1:eries can cause skin burns
or o1:her persona_ injury,
Poin% _he Remo_:e
in _he Right:
Direct:ion
and P_
i_: in DVD/V¢_
Hode
Wben you want the remote to operate the DVD/VCR, point the remote _t the DVD/VCR, not the TV.The remote hasto be pointed in tbe correct direction and toward the
correct component in order for the remote control's signal to communicate with the sensor on the component. Hake sure there is a clear path between the remote control
and the component you want to operate, so the signal isn't blocked.
Hake sure the remote is in DVD/VCR mode--press the DVD/VCR button,
Turn on _he TV _d
DVDiVCR
Is Turn on the DVD/VCg--press the DVDNCR button on the remote.
2. Turn on the TV and tune it to the correctVideo Input Channel--if you have an RCA, GE, or ProscanTV, press the TV button on the remote (if the TV doesn't turn on,
press the ON.OFF button) and then press the INPUT button on the remote until you get to theVideo Input Channel that matches how the DVD/VCR is connected to
the T\{
If you have another brand of TViturn on the TV and tune the TV to the correct Video Input Channel (if you don't Imow how to accessthe Video Input Channel on your
TV,go to page 18for help).
Note:You can programyourremote tooperatemost brandsofremote controllable
TVs. instructions
areon page2 i.
L@_ o ft_pa'
butto_
DoII/,I OtTOIi// --
button
O_-OFF
SAT
A_X
O
ZO_
ANALO_
_PE_
A_
Up afro',,',' bt,JttOl
Ri,_l_tarrow
button
_"OKbutton
Comple_ce _he interactive
Setup
The next few pagesstep you through the seriesof screensthat will appear the first time you turn on
your DVD/VCR,
Use the remote control to follow the omscreen instructions,The arrow buttons move the on-screen
highlight in the corresponding directions on the screen (up, down, left, right),
Pressthe OK button to seJecta highlighted item,
Notes:
You can access thesetupscreens from themain menu. ifyou move,geta different
program
provider f or TV shows, or changeyourconnections,
you'll need to complete the interactive
Setup
again.
if you don't see the Languageselection screen (below) the first time you turn on the DVD/VCR,
make sureyou've tunedyourTV to theVideoinputChannelthatcorresponds t otheway you've
connected theTV tothe DVD/VCR. i f you need he_p, g o topage 18.
Use the aF_ow
buttons
on the re_o%e
to move
%h_ou_h
on=screen
menus
and highlight different optio_,
Press the
OK
bu_ton
to select a menu
item Ichor: is highli_hted_
I) Selec*
on-screen
men_
ian_:_a_e
Hake sure the remote is in DVD/VCR mode (press the DVD/VCR button), If you want the on-
screen menusto appear in English, press the OK button on the remote control, If you prefer
another language, p ress the arrow' down button until that languageis highlighted.PressOK to
seJectthe language.Next, the connection screen appears,
Note: if you don't see the Languageselection screen the first time you t_rn on the DVD/VC_,
make sureyou've tunedyourTV to theVideoinputCbanne}thatcorresponds t otheway you've
connected theTV tothe DVD/VCR. i fyou need he_p, g o topage 18.
Graphics
contained
within
chis publication
are for representation
only,
_
Advertisement
