Page 1
P5RD SERIES 13 SEER Single Package Air Conditioner =Single Stage, R-410A Please read this information thoroughly and become familiar with the capabilities and use of your appliance before attempting to operate or maintain this unit. Keep this literature where you have easy access to it in the future, if a problem occurs, check the instructions...
WARRANTY IN FORMATION Important Safety Information ........A warranty certificate with full details is included with the Operating Instructions ..........Air Conditioner. Carefully reviewthese responsibilities with Cooling Operation ............. your dealer or service company.The manufacturer will not Heating Operation ............. be responsible for any costs found necessary to correct Turning the Air Conditioner Off ........
iMPORTANT SAFETY INFORMATION Operating the Indoor Blower Continuously The continuous indoor blower operation is typically used to Safety markings are used to designate a degree or level circulate the indoor airto equalize a temperature unbalance of seriousness and should not be ignored. WARNING due to a sun load, cooking, or fireplace operation.
iMPORTANT SAFETY iNFORMATiON CAUTION: Please read all instructions before servicing this equipment. Pay attention to all safety warnings and any other special This unit uses refrigerant R-410A. DO NOT use notes highlighted in the manual. Safety markings any other refrigerant in this unit.
GENERAL iNFORMATiON • Sufficient clearance for unobstructed airflow through the outdoor coil must be maintained in order to achieve The P5RD packaged air conditioner is designed only rated performance. for outdoor ground level installations and can be readily • Consideration should also be given to availability of connected to the high static duct system of a home.This unit electric power, service access, noise, and shade.
SINGLE DUCT APPLiCATiON MULTIPLE DUCT APPLiCATiON Figure 3. Single & Multiple Duct Applications AIR CONDITIONER INSTALLATION • Ductworkshould be attached directlytothe unitflanges for horizontal applications, Unpacking the Unit • For highly resistive duct systems it may be necessary It is recommended that the unit be unpacked at the to add an additional return air duct and or supply to installation site to minimize damage due to handling,...
4. Tapcollar(if necessary) to ensure engagement with the floor. However, if the floor is more than ten inches unitopening andinstall s econd screw. deep, it will only be necessary to cut a hole for the collar 5. Tighten firstscrew androtate collar clockwise sojoint on the return air box or for the insulated duct.
3.Cuta 9-1/8" x 13-1/8" h oleintheductandbendover ELECTRICAL CONNECTIONS alltabsflatontheinsideoftheheatduct. 4.Insertthedamper i ntotheductandbend overalltabs WARNING: flatontheinside oftheheatduct. 5.Seal t heopening between thefiberboard anddamper To avoid risk electrical shock, personal orflexible duct. injury, or death, disconnect all electrical power to the unit before performing any maintenance REGISTER...
• The unitrequires both powerand c ontrol circuitelectrical Grounding connections. Refertothewiringdiagram / schematic WARNING: (Figures 11 & 12, pages 14 & 15)for identification and location of unit field wiring interfaces. Make all electrical The unit cabinet must have an uninterrupted connections in accordance with all applicable codes and ordinances.
20 psig. system is correctly charged. AiR CONDiTiONER MAINTENANCE REPLACEMENT PARTS WARNING: Replacement parts are available through all Nordyne distributors. Please have the complete model and serial number of the unit when ordering replacement parts. To prevent electrical shock, personal...
Packaged Air Conditioner - Single Phase NOTES: 1. Disconnect all power before servicing. 1. Couper le courant avant de faire letretien. 2. For supply connections copper conductors only. 2. Employez uniquement conducteurs en cuivre. 3. Not suitable on systems that exceed 150 V to ground.
Page 15
Packaged Air Conditioner - Single Phase NOTES: 1. Disconnect all power before servicing. 1. Couper le courant avant de faire letretien. 2. For supply connections use copper conductors only, 2. Employez uniquement des conducteurs en cuivre. & Not suitable on systems that exceed 150 V to ground...
REFRIGERANT CHARGING TABLES Shaded boxes indicate flooded conditions. r====l Rated design values. The suction pressure will vary from design value if outdoor air flow, entering dry bulb, or entering wet bulb temperatures vary. 1. All pressures are listed psig and all temperatures in °F 2.
Page 17
REFRIGERANT CHARGING TABLES Shaded boxes indicate flooded conditions. F====lRated design values. The suction pressure will vary from design value if outdoor air flow, entering dry bulb, or entering wet bulb temperatures vary. 1. All pressures are listed psig and all temperatures in °F 2.
Page 18
REFRIGERANT CHARGING TABLES Shaded boxes indicate flooded conditions. F----I Rated design values. The suction pressure will vary from design value if outdoor air flow, entering dry bulb, or entering wet bulb temperatures vary. 1. All pressures are listed psig and all temperatures in °F 2.
Page 19
PSRD-048KA Charging Chart - Cooling refrigerant when above curve _-- Add refrigerant when below curve Liquid Temperature Figure 13. Charging Chart for PSRD-048KA Series (4Ton Units with TXVValve) OUTDOOR TEMPERATURE (°F) Suct. Press. Liq. Dis. Liq. Dis. Liq. Dis. Liq. Dis.
California to cause cancer, birth defects other reproductive harm. lntertek NORDYNE C0[VIPL_E COMFOR_,GENUINEVALUE, Specifications & illustrations subject to change without notice or incurring obligations. O' Fallon, MO I Printed in U.S.A. (09/10) 7092370 (Replaces 7092000)