Related Manuals for Hoover U5759-900
Summary of Contents for Hoover U5759-900
- Page 1 Owner's Manual Operating and Servicing Instructions www.hoover.com ® Please review this manual before operating your Hoover ® product. ®2008 Healthy Gain Investments, Ltd. All rights reserved. #5651 IC67. 3/08...
-
Page 2: Table Of Contents
Clearing Blockages ........... Parts _ accessories mail order form ......... If you need assistance: Visit our website at hoover.com. Follow the service center link to find the service outlet nearest you OR Call 1-800-944-9200 for an automated referral of authorized service outlet locations (U.S. -
Page 3: Important Safeguards
Hoover Sales and SmMce Center or Authorized Hoover Warranty Service Dealer [Depot). • Do not pull or carry b.ycord, use cord as a handle, close door on cord or pull cord around sharp edges or corners. -
Page 4: Assembling Cleaner
1. Assembling cleaner Carton contents Attach handle A. Handle section B. Cleaner body C. Hose, cleaning tools and wands {packed on cleaner). Short crevice tool only available with some models. D. Powered hand too] (some models) Remove all parts from carton and identify each item shown. -
Page 5: How To Use
2. How to use Cleaner description Operate cleaner only at voltage specified on data plate on bottom of cleaner. The assembled cleaner will look like the drawing. I. l-land]e 2. ON/OFF switch 3. Too] cover 4. Dusting brush 5. Powered hand tool°' o_ Crevicetool* (depending on model) 6. -
Page 6: Embedded Dirtfinder
ON-OFF switch Plug cord into electrical outlet. To turn cleaner ON, push switch up. To turn cleaner OFF, push switch down. Handle positions Transporting Claerryi ng cleaner aner The cleaner can Io move your l'he handle of your cleaner has three cleaner from room also be moved by positions;... - Page 7 Carpet height adjustment Handle position The cleaning carpet and rugs takes place at the nozzle {C}. When it is neces sary to raise and lower the nozzle various carpet pile heights, slide the nozzle control knob For ease in sliding knob, place handle in the {D) to the desired upright...
-
Page 8: Cleaning Tools
tool cover How to attach Cleaning tools The tool cover is Tools allow for cleaning surfaces above designed with a floor and for reaching hard to clean areas. "break- away" t4andle must be in the upright position feature which tool use. allows it to snap CAUTION:Agitator continues to rotate while Free i£... -
Page 9: Mainte_Ance
Extra reach hose* Push ON/OFF Slide hose into [P} and twist hose to switch to OFF posi- tion. Remove lock it into place. [To detach hose, regular hose from Align end cleaner, reverse procedure.) of extra reach hose Attach wands tools to the other with projections end of hose. -
Page 10: Cleaning Filters
Slide cup straight Filter assembly into cavity. Bot- The HEPA cartridge filter and pre-filter tom of cup will rest essentially self-shedding. behind grooves at bottom of cleaner Tapping the side of the dirt cup as described cavity {G). in "'How to empty dirt cup" should suffi- ciently remove dust and fine particles from I'ush latch (F} to the HEPA cartridge... - Page 11 filters Secondary and final Cleaning secondary filter Disconnect cleaner from electrical outlet. The secondary filter [.J), located behind the grill in the bottom of cleaner cavity, pro- tects the motor fl'om dirt particles. If the filter becomes dirty, remove dirt cup (Fig.
-
Page 12: Replacing Headlight
To assure effective operation, use only gen- the agitator to rotate and is important uine HOOVER belts with your cleaner. When the effective operation of the cleaner. purchasing a new belt, ask for Hoover part helt is located under... -
Page 13: Replacing Agitator Brush Roll
Discard old agitator. ask For When purchasing a new agitator, Continue following the directions in "The Hoover part No. 48414132. belt" section to reposition belt, new agitator How to replace and bottom plate. Disconnect cleaner from electrical outlet. Remove bottom... -
Page 14: Replacing Edge Groomers
Powered hand tool (some models only) Agitator brush roll replacement When agitator brush roll brushes are worn, the brush roll should be replaced. Ask for HOOVER part No. 48414t How to replace I. Remove tool from hose and turn it so bottom... -
Page 15: Replacing Belt
Therefore, do not add lubricant to motor bearings. The agitator is equipped with two ball bearings that should be lubri- cated periodically by a Floover Sales and Service Center or an Autho- rizecl Hoover Warranty Service Dealer (Depot). -
Page 16: Thermal Protector
If further assistance is needed, conlact To obtain approved HOOVER service and genuine HOOVER parts, locate the nea Hoover Consumer Response Center, est Hoover Salcs and Service Center or Phone: 1-800-263-6376. Authorized 14oover Warranty Service Dealer In Canada, contac[ Hoover Canada,... -
Page 17: Tf You 14Avea Problem
4. If you have a problem If a minor problem occurs, it usually can be solved quiteeasily when the cause is Found by using the check list below. POSSIBLE CAUSE POSSIBLE s6i.UnoN PROBLEM Cleaner won't run No voltage in wall plug Check fuse or breaker Thermal protector activated... -
Page 18: Clearing Blockages
!PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION , ,, ,,, Powered hand tool Continue using tool applying lighi pres- Too much pressure being (some models) applied to tool SU re. brush roll won't _e,_.:.:::_ .: , v_,'_..,,_.,_ :_.:_:.._:_,_- :_:._ ..... -._._._ _,, _ .._,_,__ ...... -
Page 19: Parts _ Accessories Mail Order Form
Day Phone ( Signature (req.) Replacement parts and accessory items may be purchased from your Authorized Hoover Dealer, Leading Retailers, Hoover Sales & ServiceCenters, on-line at www.hoover.com, or by completing this order form Mail orderslimitedto U.S.residents only. In Canada,pleasecall 1-800-263-6376 ORon-line at hoover.ca...