Related Manuals for Hoover U5725960
Summary of Contents for Hoover U5725960
- Page 1 ™ TurboPOWER ™ WindTunnel Bagless by HOOVER Congratulations on your purchase! ® This product was designed for easy assembly (see page 3) www.hoover.com...
-
Page 2: Table Of Contents
• Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot). -
Page 3: Assembling Cleaner
This cleaner was inspected and packaged carefully before being shipped from the factory. If you should happen to need assistance during assembly or operation, call: Visit us on-line at www.hoover.com to find the service outlet nearest you (click on the “Service” button) OR 1-800-944-9200 for an automated referral of service outlet locations (U.S. - Page 4 STEP 1 Attach handle Remove cardboard (A) and screws Open tool cover on cleaner body Make sure that the switch is in the from handle section. Discard card- (B). OFF position. board. Remove powered hand tool. Remove switch lock (C) above ON/ Slide handle section onto back of handle.
-
Page 5: Cleaner Description
2. How to use Cleaner description The assembled cleaner will look like the drawing. 1. Handle 20. Hose rack 2. ON/OFF switch 21. Cord hooks: wrap cord around hooks for 3. Tool cover storage. The top hook 4. Dusting brush can be rotated right or 5. -
Page 6: Carpet Height Adjustment
Carpet height Settings Handle position adjustment For ease in sliding knob, place handle For maximum cleaning performance, in the upright position and tilt cleaner the following carpet height settings are The cleaning of carpet and rugs takes recommended. forward (C). place at the nozzle (A). -
Page 7: Cleaning Tools
Cleaning tools 2-11 2-12 Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas. Handle must be in the upright posi- tion for tool use. CAUTION: Agitator continues to rotate while cleaner handle is in upright position. -
Page 8: Cleaning Filters
When to empty 3. Maintenance It is recommended that the dirt cup be Familiarize yourself with these home emptied before the dirt reaches the dirt maintenance tasks as proper use and inlet opening on back of dirt cup (Fig. 3-1) care of your cleaner will ensure contin- or after every use if preferred. -
Page 9: Cleaning Secondary Filter
Reposition dry filter, grill and screw. Replace dirt cup. Should you want to replace this filter, ask for HOOVER part No. 38762008. Let filter air dry and reposition it on the 3-12 3-13 side of cleaner. Make sure the white side of the filter faces outward. -
Page 10: Replacing Headlight
What to buy we strongly recommend you check for This cleaner uses a 12 volt, wedge base debris accumulation under the agitator type 912 bulb, HOOVER part No. shield each time you clean the filters. 27313101. Removing debris under the shield will help maintain your cleaner’s excellent... -
Page 11: Replacing Agitator Brush Roll
What to buy When purchasing edge groomers, ask for HOOVER part No. 39511004. Installing groomers How to replace Lift off both old edge groomers and slide Disconnect cleaner from electrical new edge groomers into position as outlet. -
Page 12: Agitator Brush Roll
Agitator brush roll replacement When agitator brush roll brushes are worn, the brush roll should be replaced. Ask for HOOVER part No. 48414088. 3-25 3. Remove agitator including end plates 2. Unscrew the two Phillips screws and (C) and discard. -
Page 13: If You Have A Problem
Hoover Company on-line at • Incorrect carpet height setting roll won’t turn www.hoover.com • Move nozzle control knob to lower Do not send your cleaner to The Hoover setting Possible cause Company in North Canton for service, • Blockage in air flow passage Possible solution this will only result in delay. -
Page 14: Clearing Blockages
The Hoover Company on-line at www.hoover.com This warranty does not cover pick up, delivery, or house calls; however, if you mail your appliance to a Hoover Factory Service Center for warranty service, Check dirt duct transportation will be paid one way.