Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Fedders 23-23-0262N-005
Summary of Contents for Fedders 23-23-0262N-005
- Page 1 Including Service Warranty lncluidos mantenimiento y la garantJa Avec service et garantie iill IIII _ Room Air Conditioners for Double-Hung Windows Acondicionadores de aire ambientai para ventanas dobles Ciimatiseur d'air individue! pour fen_tres _ guillotine 10,000 BTUt5 5,000-...
- Page 2 IIIII I L,., • _,:, ESPA/ OL ENGLISH FRANC AIS Requistos para Exigences 61ectrique ..Electrical Requirements ..1. Avertissement Warning la el_ctricos ....... Avis Notice Aviso ImportanteS exigences de raise_ la terre Important Grounding Requirements Aviso Requis'tos i mporrantespara la conexi6n a tierra Installation ......
- Page 3 1. ELECTRICAL REQUIREMENTS Product Damage: DO no( cut, aker o¢ Rmov_ any ol the ¢q:mnded polv_,,_rene Electrical Shock Hazard (while _ inside this a_ conditmne_. ' " Grounded three-prong Single outlet grounding Plug unit only into _rounded electrical ourdet. wall receptacle wall receptacle For YourSafety:.
-
Page 4: Filler Panel Installation
3. WINDOW INSTALLATION 2. FILLER PANEL INSTALLATION installation in Window Opening 22 7/8" to 39" Wide 1. Open and mark center line of window. • Center line bracke Filler panel, 2. Securethe an_le bracket on the center of' the window silt with two (2) 1" long screws [Fig. - Page 5 4. Keeping a firm grip on air conditioner, care- fully center air conditioner in window open- ing with the bottom bar between the window stool and the angle bracket {if the bracket is too short to hold the unit in position, insert a filler board to make it taller).
- Page 6 3. WINDOW INSTALLATION Plaslic foamseal Installation Upper window sash Window Opening 20 1/4" to 22 718" Wide 1. Remove filler panels from cabinet (Fig. $). 2. Refer to steps I through 4 of preceding instructions (Pgs. 2 & 3). Lower window sash 3.
-
Page 7: Operation
IIIIIIIII 4. CONTROL PANEL air circulation or air cir- Heating Operation culation without cooling Heating Models Only or heating. 2, Thermostat: Controls t. Turn Thermostat Control to position "I ". unit thermostat, which 2. Turn Master Control to HIGH HEAT. regulates room tempera- 3. - Page 8 5. FRONT PANEL Directing Airflow Decorative Front (Unit with fixed louvers) Unit is engineered with two fixed bank louvered inserts to direct discharge airflow. To adjust direc. tion of airflow either right or left, proceed as follows: 1o Remove front panel. Position louvered insertsto give desired airflow direction.
- Page 9 - --T ---- 4. Gently twist with the screwdriver and unlock the plastic projection by pulling the decora- tive front slightly forward. 5. Swing the left side of the decorative front away from the cabinet and unhook the Model andserial number plastic projection on the right.
-
Page 10: Warranty
TurnMaster Control to HIGH FAN. If air cir- During the first year after the date of original put. Shut all windows and doors in room. chase, Fedders North America will, through its culating fan does not operate, check house authorized servicers and free of charge to the Remove any obstructions from inside circuit breaker (or fuses). - Page 11 Write down model M_iei andse_l number Ndmerosde serle serial numbers Num_'osde modile You'll End them on a label behind the air dis- charge grill. They'll be easier to mad if you shine a flashlight on them or remove the front panel. Use these numbers in any correspondence or service calls concerning your air conditioner.
Need help?
Do you have a question about the 23-23-0262N-005 and is the answer not in the manual?
Questions and answers