Related Manuals for Hoover WindTunnel U8146-900
Summary of Contents for Hoover WindTunnel U8146-900
- Page 1 WindTunnel with Technology HOOVER Thank your purchase! Owner's Manual ENGLISH -_ pp.1-1 ESPANOL-_ pag, 14-21 FRAN(_AIS "_ p. 23-30 This product was designed for easy assembly (see page 3) www.hoover.com...
-
Page 2: Before Using This Appliance
If appliance is not working as it should, been dropped, damaged, left outdoors, or dropped into water, take it to a Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer (Depot). _ 2002 The Hoover •... - Page 3 If you need any assistance: www.h00ver.c0m. Visit website Click on the "Service" button to find service outlet nearest Call 1-800-944-9200 an automated referral of service outlet locations (U,S, only) Call 1-330-499-9499 speak with a representative in our Consumer Response Center. Please do not return this product to the store.
- Page 4 Cleaner Assembly 1151 Push Snap tabs hose holder into Remove cardboard four switch down position. screws from handle section. Discard holes handle section. cardboard, keep screws assembly 1-7 and 1-8), (Figs, iiii Push screws into holes back Slide handle section onto back Place...
- Page 5 assembled cleaner will look like drawing. Cleaner description 1. Handle 20. Cord hooks: wrap cord around hooks 2. ON/OFF switch storage. hook 3. Tool cover rotates right left 4. Dusting brush easy cord release. 5. Powered hand tool 21. Carrying handle 6.
- Page 6 posl :ion Setti n g s Carpet height For maximum cleaning performance, ease sliding knob, place handle adjustment in the upright position tilt cleaner following carpet height settings cleaning carpet rugs takes forward. recommended. place nozzle (B), C_ Lowest setting: bare floors When...
-
Page 7: Edge Cleaning
Cleaning tools ,a., cleaner han- When using cleaning tools, dle should be in the upright position to activate the automatic "brush roll OFF" and for convenience in moving .._- the cleaner from one area to another. Edge cleaning Select proper tool G. - Page 8 How to When empty empty recommend that dirt Familiarize yourself withthese home emptied before dirt reaches dirt maintenance tasks. P roper car_ (Fig, 3-1) openinc] back after your cleaner will ensure continued every if you prefer. cleaning effectiveness. CAUTION: Very fine materials, such as face powder...
- Page 9 Oleaning final filter filter reposition Replace door, Snap closed, Should want replace this filter, for HOOVER part No. 38766028. Do not operate cleaner without the fil- ter in place. Slide filter assembly down into until a light snap felt.
- Page 10 Headlight replacement What This cleaner uses volt, wedge base type 91 2 bulb, HOOVER part No. 27313107. Remove lens - Disconnect cleaner Install bulb - Pu, old bulb straight out from electrical outlet. Push socket. bulb straight into socket until...
-
Page 11: How To Replace
Powered hand tool Agitator brush roll replacement When agitator brushes worn, brush roll should replaced. HOOVER part No. 48414088. Remove agitator including plates Unscrew Phillips screws discard. remove belt guard (B). Inspect belt ensure that it is good condition. If belt... - Page 12 • Reset circuit breaker described dirt from spinning without affecting 2-9. Fig. Hoover Cleaning cleaning performance. cleaner • Agitator brush rolls worn continue used even if the dirt Perform a n c e • Replace [)rush...
- Page 13 U.S.A., phone 1-800-944-9200 genuine HOOVER parts, locate Hoover Factory Service nearest visit The Hoover Company on-line at Center or Authorized Hoover www.hoover.com Warranty Service Dealer (Depot) This warranty does (-;over pi(;k Pages • _;hecking...
- Page 16 HOOVER et_sont marques deposees HOOVER y marcas registradas registered trademarks 5-02 U8130-/40-900 Printed in Mexico 56511 -B47...
Need help?
Do you have a question about the WindTunnel U8146-900 and is the answer not in the manual?
Questions and answers