GE GLD5604VWW Owner's Manual page 7

GEAppliances.com
_t_ Options
The light above the selected pad will be ON to indicate which OPTION has been selected.
STEAM(Prewash) Use this option to improve wash performance with heavy or dried-on soils. This option is available
(on some with all cycles except RINSE ONLY.
models)
HOT WASH/ Use this option to improve wash and dry performance with heavy or dried-on soils.
HI-TEHP WASH/ This option must be selected prior to starting the cycle. It cannot be selected with RINSE ONLY or
ADDED HEAT CHINA/CRYSTAL cycle.
(on some models)
HOT START Use this option to improve wash and dry performance where inlet water temperature is low.
(on some models)
HEATED DRY Shuts off the drying heat option. Dishes air dry without using energy.
Light OFF For faster air dry you can prop the door open after the CLEAN light illuminates.
HEATED DRY Turns the heater on for fast drying. This will extend the total run time between 54 and 45 minutes
Light ON depending on the cycle selected.
NOTE: Cannot be selected with RINSEONLY
CONTROL
LOCK
(on some
models)
DELAY HOURS
You can lock the controls to prevent selections from being made. You can also lock the controls
after you have started u cycle to prevent uninterrupted cycle changes.
For example, children cannot accidentally start the dishwasher by touching pads with this option selected.
ToLOCK the dishwashercontrol, touch and holdthe HEATED DRYpad for 3 seconds. T helightto the left of the
HEATED DRYpadwill turn on.ToUNLOCK the dishwashercontrol,touch and holdthe HEATED DRYpad for 3 seconds.
TheLOCK lightwill turn off.
You can delay the start of a wash cycle for 2, 4 or 8 hours (delay time options may vary by model)
Touch the DELAYHOURS pad to choose the number of hours you want to delay the start of the
cycle; then touch START/RESET one time. A single beep will confirm DELAYHOURS has been set. The
dishwasher will count down and start automatically at the correct time. Touching START/RESET a
second time will cancel DELAYHOURS and turn off the dishwasher.
NOTE:While DELAYHOURS is active (after the START/RESET pad has been pressed), the dishwasher
will update the remaining count down time on the control panel before the dishwasher starts the
cycle. For example, if DELAYHOURS8 is selected, the delay hour indicator will move from 8 to 4 to 2
to off as delay time elapses.
START
RESET
Close and latch the dishwasher door and select the cycle and desired options. Touch the
START/RESETpad one time to begin the cycle. Water begins to fill the dishwasher, and approximately
60 seconds later the wash action begins.
NOTE:The dishwasher remembers your last cycle so you don't have to reprogram each time.
When the dishwasher door is closed and latched, the control panel lights will display the last
settings selected.
If you don't want to change any of the settings, simply touch the START/RESET pad once to begin the cycle.
If the door is closed, the indicator lights will turn off if a pad is not pressed within two minutes.
To activate the display, open and close the door or touch any pad.
If a power failure occurs, NORMAL WASH and HEATEDDRY will automatically be programmed.
To change cycles after washing starts, press the START/RESET pad. This will cancel the currently
running cycle, and begin pump-out. During this time, the LEDsof the currently selected cycle
will flash. Once the pump-out is complete, the dishwasher will turn off.
Press the START/RESET pad when the dishwasher is running to cancel the cycle. The dishwasher will
pump out and turn off at the end of pump-out. The LEDs of the currently selected cycle will flash
during pump-out. You can select cycles and options during pump-out. If you press START/RESET
during the pump-out period, the pump-out will stop and a new cycle will begin.