Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Packard Bell MX
Summary of Contents for Packard Bell MX
- Page 1 Packard Bell EasyNote MX Disassembly Manual...
-
Page 2: Table Of Contents
LCD Screen Assembly ..........................9 Main Board ............................11 Modem ..............................12 Bluetooth (Optional) ..........................13 Touchpad...............................13 Speakers ...............................14 Subwoofer (Optional) ..........................14 LCD Panel .............................15 Inverter Board............................16 Webcam ..............................16 Webcam Microphone/USB Cable ......................17 WLAN Antenna ............................17 Notice ..............................18 Packard Bell EasyNote MX Disassembly Manual... -
Page 3: Overview
Packard Bell reserves the right to make changes to the EasyNote MX without notice. Technician Notes Only technicians authorized by Packard Bell B.V. should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. -
Page 4: Hazardous Voltage
Non personal injury. Always return a defective power avviare il sistema senza aver prima messo supply to the dealer. a posto il coperchio. Packard Bell EasyNote MX Disassembly Manual... -
Page 5: Battery
2. Pull the plastic tab on the hard disk drive towards you as shown in Fig. 2 to disconnect the drive. Fig. 2 Removing hard disk drive. 3. Take the drive out of its compartment. Packard Bell EasyNote MX Disassembly Manual... -
Page 6: Optical Disk Drive
3. Take out the optical disk drive from the drive bay. WLAN Card To remove the WLAN card, first remove the battery (see Battery) and then perform the following steps: 1. Remove the 7 screws retaining the CPU cover (see Fig. Packard Bell EasyNote MX Disassembly Manual... -
Page 7: Memory
4. Take out the WLAN card from the slot. Memory To remove the memory installed, first remove the battery (see Battery) and then perform the following steps: Remove the 7 screws retaining the CPU cover (see Fig. Packard Bell EasyNote MX Disassembly Manual... -
Page 8: Processor
1. Remove the 7 screws retaining the CPU cover (see Fig. 2. Remove the 2 screws holding the CPU fan. Fig. 8 Location of CPU fan screws. 3. Disconnect the power cable and remove the CPU fan cover. Packard Bell EasyNote MX Disassembly Manual... -
Page 9: Keyboard
1. Remove the 7 screws retaining the CPU cover (see Fig. 2. Remove the 4 screws labelled K>. Fig. 10 Location of K> screws. 3. Turn the notebook over so the top is facing up. Packard Bell EasyNote MX Disassembly Manual... -
Page 10: Lcd Screen Assembly
Card), and then perform the following steps: 1. Turn the notebook upside down. 2. Remove the 4 screws shown in Fig. Fig. 12 Removing 4 bottom screws. 3. Turn the notebook over so the top is facing up. Packard Bell EasyNote MX Disassembly Manual... - Page 11 Fig. 15 Location of screw in hinge. 9. Turn the notebook upside down. 10. Remove the tape (if used) securing the WLAN antenna cable and unhook it from the plastic tabs. Fig. 16 The wireless antenna cable. Packard Bell EasyNote MX Disassembly Manual...
-
Page 12: Main Board
2. Remove the 4 screws that were covered by the LCD screen and the 4 screws in the heat plate. Fig. 17 Location of screws. 3. Turn the notebook upside down. 4. Remove the 4 small screws in the hard disk drive compartment. Fig. 18 Location of screws in HDD compartment. Packard Bell EasyNote MX Disassembly Manual... -
Page 13: Modem
Board), and then perform the following steps: 1. Disconnect the modem cable from the modem. 2. Remove the 2 screws securing the modem and take out the modem. Fig. 20 Location of modem screws. Packard Bell EasyNote MX Disassembly Manual... -
Page 14: Bluetooth (Optional)
Assembly), the main board top cover up to step 7 (see Main Board), and then perform the following steps: 1. Remove the 2 screws securing the touchpad buttons board to the top cover. Fig. 22 Location of touchpad buttons board. Packard Bell EasyNote MX Disassembly Manual... -
Page 15: Speakers
Assembly), the main board top cover up to step 7 (see Main Board), and then perform the following steps: 1. Disconnect the subwoofer cable from the main board. Fig. 24 Disconnecting the subwoofer cable. Packard Bell EasyNote MX Disassembly Manual... -
Page 16: Lcd Panel
2. Remove the 5 screws that appeared after removing the rubber stoppers (see Fig. 26). 3. Carefully remove the LCD cover which has been clicked into place. 4. Disconnect the power cable from the inverter board. Fig. 27 Location of inverter board. Packard Bell EasyNote MX Disassembly Manual... -
Page 17: Inverter Board
Assembly), disassemble the LCD panel up to step 3 (see Panel), and then do the following: 1. Disconnect the cable from the webcam. Fig. 29 Location of webcam connector. 2. Lift out the webcam. Packard Bell EasyNote MX Disassembly Manual... -
Page 18: Webcam Microphone/Usb Cable
Assembly), disassemble the LCD panel up to step 5 (see Panel), and then do the following: 1. Remove the wireless antenna from the shielding foil in the LCD cover. Fig. 30 Location WLAN antenna cables. Packard Bell EasyNote MX Disassembly Manual... -
Page 19: Notice
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from Packard Bell B.V. PACKARD BELL B.V. SHALL NOT BE HELD LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;...
Need help?
Do you have a question about the MX and is the answer not in the manual?
Questions and answers