Craftsman 315.101390 Owner's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Drill
  5. 315.101390
  6. Owner's manual

Craftsman 315.101390 Owner's Manual

1/2 inch hammer drill double insulated
Hide thumbs
Table of Contents

Advertisement

Quick Links

OWNER'S
MANUAL
MODEL NO.
315.101390
CAUTION:
Read and follow
ALL safety rules
and instructions
before operating
this equipment.
CRRFTSMRN°
1/2 Inch
Hammer Drill
DOUBLE INSULATED
Thank
You for Buying
A
Craftsman
Hammer
Drill
Rules for Safe Operation
Warranty
Operation
Maintenance
Repair Parts
SEARS, ROEBUCK AND CO., Hoffman Estates,
IL 60179
U.S.A.
®
972000-148
9-00
Printed In U.S.A.

Advertisement

Table of Contents
loading

Related Manuals for Craftsman 315.101390

Summary of Contents for Craftsman 315.101390

  • Page 1 Hammer Drill before operating this equipment. DOUBLE INSULATED Rules for Safe Operation Warranty Thank You for Buying ® Operation Craftsman Hammer Drill Maintenance Repair Parts SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. 972000-148 9-00 Printed In U.S.A.

  • Page 2: Rules For Safe Operation

    RULES FOR SAFE OPERATION DOUBLE INSULATION is a concept in safety, in electric IMPORTANT - Servicing of a tool with double insulation power tools, which eliminates the need for the usual three requires extreme care and knowledge of the system and should be performed only by a qualified service technician.
  • Page 3 Outdoor approved cords alcohol, or any medication. are marked with the suffix W-A, for example WHEN SERVICING ONLY IDENTICAL SJ-IW-A or SJOW-A. CRAFTSMAN REPLACEMENT PARTS. KEEP BITS CLEAN SHARP. Sharp bits POLARIZED PLUGS. To reduce the risk of electric minimize stalling and kickback.

  • Page 4: Specifications

    IT TO THE NEAREST SEARS STORE IN THE UNITED STATES, and Sears will repair it, free of charge. if this Craftsman Hammer Drill is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase.

  • Page 5: Operation

    OPERATION ELECTRICALCONNECTION WARNING: Your hammer drill has a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not Always wear safety goggles or safer,/glasses with side operate this tool on direct current (DC).
  • Page 6 OPERATION SWITCH See Figure2. To turn your hammer drill ON, depress the switch trigger. Release switch trigger to turn your hammer drill OFF. LOCK-ON BUTFON See Figure 2. Your hammer drillis equipped with a "lock-on" feature, which is convenient when continuous drilling for extended periods of time is required.
  • Page 7 OPERATION VARIABLE SPEED See Figure5. Your hammer drill has a variable speed control selector designed to allow operator control and adjustment of speed and torque limits. Speed and torque can be increased or decreased by rotating the variable speed control selector in the direction of the arrows shown in figure 5.

  • Page 8: Installing Auxiliary Handle

    OPERATION INSTALLING AUXILIARY HANDLE (Continued) NOTE: For convenience the screw has been trapped inside TIGHTEN the auxiliary handle. AUXILIARY HANDLE • Remove depth gage clamp and auxiliary handle from ANDCLAMP plastic bag in hammer drill box. • Orient depth gage clamp so that the tabs will fit into DEPTH motor housing of hammer drill, GAGE...
  • Page 9 OPERATION TO INSTALL BITS See Figure 9. CHUCK • UNPLUG YOUR HAMMER DRILL. Failure to unplug your hammer drill could result in accidental starting causing serious injury. DRILL • Open or close the chuck jaws to a point where the CHUCK opening is slightly larger than the drill bit you intend to JAWS...

  • Page 10: Wood Drilling

    OPERATION DRILLING See Figure 1 I. • Depress and release switch trigger to be sure your drill is in OFF position before connecting it to power supply. • Check the direction of rotation lever for correct setting (forward or reverse). See Figure 3. •...

  • Page 11: Chuck Removal

    OPERATION CHUCK REMOVAL See Figures 12, 13, and 14. The chuck must be removed in order to use some accessories. To remove: • UNPLUGYOUR HAMMER DRILL. Failure to unplug your hammer drill could result in accidental starting causing serious injury. •...

  • Page 12: Maintenance

    The chips and grindings from thee When servicing use only identical Craftsman replacement materials are highly abrasive to electric tool parts such a parts. Use of any other parts may create a hazard or cause bearings, brushes, commutators, etc.
  • Page 13 NOTES Page 13...
  • Page 14 CRAFTSMAN 1/2 INCH HAMMER DRILL-- MODEL NUMBER 315.101390 ... 13 14 SEE NOTE _A" PAGE...

  • Page 15: Parts List

    CRAFTSMAN 1/2 INCH HAMMER DRILL- MODEL NO. 315.101390 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your 1/2 INCH HAMMER DRILL or when ordering repair parts.
  • Page 16 For repair of major brand appliances in your own home... no matter who made it, no matter who sold it! 1-800-4-MY-HOME sM Anytime, day or night (1-800-469-4663) www.sears.com To bring in products such as vacuums, lawn equipment and electronics for repair, call for the location of your nearest Sears Parts & Repair Center. 1-800-488-1222 Anytime, day or night...

Table of Contents