Advertisement
ELECTRICAL
CONNECTIONS
WARNING:
All electrical connections must be per-
formed by a qualified electrician. Make sure unit is off
and disconnected from power source while motor is
mounted, connected, reconnected or anytime wiring is
inspected.
•
Drill press motor can be wired for 115 or 230 volts,
single-phase operations.
•
Motor must rotate in clockwise direction facing shaft
end of motor
•
See wiring diagram (Figure 3) for wiring instructions,
single-phase operation.
U
115V
V
U
230V
V
1,2, 3, 4, 5,6-
Motor Leads
L1, L2 - Digital Readout Leads
U, V -
Power Supply
Figure 3 - Motor and Digital Readout Wiring Diagram
DESCRIPTION
Craftsman
15" Variable Speed Professional Drill Press
features a fine grain cast iron base, table and head.
Spindle speeds are infinitely variable from 300 to 3300 1
RPM. Drill press includes arbor with Jacob taper #6,
chuck with key and drill press guard. Spindle travels 5" !
and has scale and depth control,
i
Large 12Y8x 16" table rotates around column. Table
surface is precision ground and features T-slots, water
trough and easy height adjustment to handle most
drilling operations.
1 HP motor can be wired for 115 or
230 volt operation.
SPECIFICATIONS
Infinitely Variable Speed ............
300-3300 RPM
Table size ...........................
127/8 x 16"
T-stots .............................
2 each, %"
Swing ..................................
15"
Arbor taper ......................
Jacob taper #6
Quill diameter ...........................
2.16"
Spindle diameter .........................
1.74"
Maximum distance table to spindle
...........
25'/2"
Overall height: ...........................
70'/,"
Shipping weight: ........................
450 Ib
OPERATION
SAFETY
RULES
WARNING:
For your own safety, read all of the
instructions and safety precautions before operating drill
press.
WARNING:
Operation of any power tool can result in
foreign objects being thrown into eyes which can result
in severe eye damage. Always wear safety goggles
complying with United States ANSI Z87.1 (shown on
package) before commencing power tool operation.
•
Know general power tool safety. Make sure all pre-
cautions are understood (see pages 2, 3, and 5).
•
Always wear eye protection or face shield.
•
Do not wear loose clothing, gloves, neckties, rings,
bracelets or other jewelry.
• Whenever adjusting or replacing any parts on drill
press, turn switch off and remove plug from power
source.
•
Make sure all moving parts are free from interference.
•
When drilling in material that causes dust, a dust
mask shall be worn.
•
Non-slip footwear and safety shoes are recommend-
ed.
•
Do not plug in drill press unless switch is in "off"
position. After turning switch on, allow drill press to
come to full speed before operating.
•
Keep hands clear of all moving parts.
•
Use recommended
speed for drill accessory and
workpiece material.
•
Drill press head and table shall be securely locked to
column before operating drill press. This must always
be checked prior to starting machine.
•
Secure workpiece using either clamps or a vise to
drill press table.
•
Never brush away any chips while machine is in
operation. All clean up should be done when
machine is stopped.
•
Make sure the machine is securely mounted to floor.
•
Make sure drill bits are properly secured.
•
Make sure drills are sharp.
•
Disconnect power when changing bits.
•
Keep lightly lubricated as directed,
•
Always keep hands and fingers clear of the
descending head and the turning bit.
•
Make sure all included covers and guards are in
place and secured before operating the drill press.
•
Do not leave drill press running when it is unattended.
•
Keep children away from the drill press at aUtimes.
•
Do not operate drill press when you are tired, ill or on
medications that affect your emotional or physical sta-
bility.
• Turn switch off and disconnect power whenever drill
press is not in use.
•
Keep drill press maintained. Follow maintenance
instructions (see pages 6 and 7).
5
Advertisement
