Download
Share
Print this page
Craftsman 351.229350 Operator's Manual
  1. Manuals
  2. Brands
  3. Craftsman Manuals
  4. Power Tool
  5. 351.229350
  6. Operator's manual
Craftsman 351.229350 Operator's Manual

Craftsman 351.229350 Operator's Manual

15" variable speed floor model drill press
Hide thumbs

Advertisement

Quick Links

Download this manual
Operator's Manual
CRRFTSMRN o
15" VARIABLE SPEED
FLOOR MODEL DRILL PRESS
Model No.
351.229350
CAUTION:
Read and follow
all Safety Rules and Operating
Instructions
before First Use
of this Product.
Sears, Roebuck and Co., Hoffman
Estates,
IL 60179 U.S.A.
16314.00 Draft (01/03/00)

Advertisement

loading

Related Manuals for Craftsman 351.229350

Summary of Contents for Craftsman 351.229350

  • Page 1 CRRFTSMRN o Operator's Manual 15" VARIABLE SPEED FLOOR MODEL DRILL PRESS Model No. 351.229350 CAUTION: Read and follow all Safety Rules and Operating Instructions before First Use of this Product. Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. 16314.00 Draft (01/03/00)
  • Page 2 PREPARE WORK AREA FOR JOB • Keep work area clean. Cluttered work areas invite Warranty ........accidents. SafetyRules ......• Do not use power tools in dangerous environments. Unpacking ......... • Do not use power tools in damp or wet locations. Do Assembly.........

  • Page 3: Mount Drill Press

    • Knowyourtool.Learn the tool'soperation, applica- • Insert arbor into spindle, push arbor into spindle and tionandspecificlimitations. twist arbor slightly to release air trapped in taper. • Userecommended accessories ( refer to page13). • Mount chuck onto arbor, push chuck over arbor and Useof improper a ccessories m aycauseriskof twist arbor slightly to release air trapped in taper.
  • Page 4 GROUNDING INSTRUCTIONS Make Sure This Grounding WARNING: Improper connection of equipment Is Connected grounding conductor can result in the risk of electrical To A Known Ground shock. Equipment should be grounded while in use to 3-Pron protect operator from electrical shock. •...

  • Page 5: Specifications

    Drill press head and table shall be securely locked to column before operating drill press. This must always DESCRIPTION be checked prior to starting machine. Craftsman 15" Variable Speed Professional Drill Press • Secure workpiece using either clamps or a vise to features a fine grain cast iron base, table and head.
  • Page 6 SPEED ADJUSTMENT Pull plunger pin out and pivot guard assembly up. After changing bit and before operating drill press, WARNING: Be sure motor is running when adjusting be sure to flip guard assembly down with plunger spindle speed. Damage to drill press may result if spin- seated securely in clamp.
  • Page 7 • Loosen hex nuts (Key. No. 56) on hex head bolts belt between pulleys. Be careful not to pinch fingers (Key. No. 64). Pivot motor mount plate (Key. No. 63) between pulley and belt. towards head. • Pivot motor away from head and secure position with hex nuts.
  • Page 8 SYMPTOM POSSIBLE CAUSE(S) CORRECTIVE ACTION Spindle does not turn 1. No power to drill press 1. Check wiring, fuse or circuit breaker 2. Defective switch 2 Replace switch 3. Defective motor 3. Replace motor Noisy spindle Defective bearings Replace bearings Noisy operation 1.
  • Page 9 Model 351.229350 Figure 4 - Replacement Parts Illustration for Guard PART NO. DESCRIPTION QTY. 02580.00 '/,-20 x 1'12"Socket Head Bolt 08431.00 Spring (set of 2) 08432.00 Lower Guard 08433.00 Adjustment Knob Assembly 08434.00 Shield with Mounting Pin 08912.00 Guard (Key Nos. 1-5) Standard hardware item available locally.
  • Page 10 Model351.229350 Figure 5 - Replacement Parts Illustration for Head _"65...
  • Page 11 PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. 15840.00 15184.00 , Gear Box Pulley Cover 16000,00 Bottom Plate 15841.00 Digital Readout with Screws 5-0.8 x 12mm Socket Head Bolt 05318.00 5-0.8 x 12mm Flat Head Screw 05331.00 12-1.75mm Fiber Hex Nut Cover 05358.00 15171.00...
  • Page 12 Model 351.229350 Figure 6 - Replacement Parts illustration for Lower Head Components 22 _._--,-_- 0 18 "_" _..17...
  • Page 13 PART NO. DESCRIPTION QTY. PART NO. DESCRIPTION QTY. 16016,00 Head 00989.00 _204ZZ Rearing 00256,00 07826.01 3AMI-20 Retaining Ring Flange 01760,00 6-1.0 x 16mm Socket Head Bolt 08641.00 Rubber Ring #10-24 Hex Nut* 02576.00 STD541010 10-1.5 x 40mm Dog Point #10 Serrated Washer Set Screw 01474.00 STD551010...
  • Page 14 Model351.229350 Figure 7 - Replacement Parts Illustration for Base and Table...
  • Page 15 PART DESCRIPTION QTY. 15134.00 Column Assembly 15161.00 Base 16311.0O 12-1.75 x 25mm Socket Head Bolt STD852012 12mm Lock Washer* STD851012 12ram Flat Washer* 15136.00 Rack 15163.00 Table Collar 15164.00 00351.00 6-1.0 x 10mm Set Screw 05989.00 3AM1-14 Retaining Ring 15165.00 Shaft 15166.00 Worm Gear...
  • Page 16 In U.S.A. or Canada for in-home major brand repair service: Call 24 hours a day, 7 days a week 1-800-4-MY-H O M ES°(1-800-469-4663) Para pedir servicio de reparaci6n a domicilio - 1-800-676-5811 Au Canada pour tout le service - 1-877-LE-FOYER _M (1-877-533-6937) For the repair or replacement parts you need:...