Advertisement
Warranty .......................................
2
Safety Rules ....................................
2
Operation
....................................
2-4
Maintenance ....................................
4
Troubleshooting
.................................
5
Parts Illustration and List .........................
6-7
FULL
ONE YEAR WARRANTY
ON CRAFTSMAN
AIR-DRIVE
TOOLS
If this Craftsman air-drive tool fails due to a defect in material
or workmanship within one full year from the date of purchase,
return it to the nearest Sears Service Center in the United
States, and Sears will repair it free of charge.
If this air-drive tool is used for commercial purposes, this
warranty applies for only 90 days from the date of purchase.
This warranty gives you specific legal rights and you may also
have other rights which vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL
60179
°
Air tool operators and all others in work area should
always wear safety goggles complying with United States
ANSI Z87.1 to prevent eye injury from fasteners and flying
debris when loading, operating or unloading this tool.
*
Never exceed operating pressure of 100 PSI.
°
Always keep hands and body away from the fastener dis-
charge area when air supply is connected to tool.
*
Always disconnect tool from air supply when servicing or
adjusting tool and when tool is not in use.
*
Do not operate when nose of tool is not in contact with
work.
°
Never load the tool until you are ready to use it.
*
Never depress tool trigger when loading.
°
Always load with nose of tool pointing away from you and
others.
*
Never point tool at yourself or others.
*
Never carry tool with trigger depressed.
°
Do not use oxygen, combustible gas or high pressure
compressed
gas as the air supply for the tool.
°
Always use tool at safe distance from other people in work
area.
*
Do not attempt to discharge fastener into hard or brittle
materials such as concrete, steel or tile.
*
Do not connect female quick-disconnect
coupling to tool
side of air line.
*
Connect male, free-flow nipple to tool side of air line
connection so that tool is depressurized
when hose is
disconnected.
*
Do not use a hose swivel with this tool.
*
Use Sears recommended
fasteners only.
DESCRIPTION
The Craftsman ¼" Crown Stapler drives ¼" crown, 18 gauge
staples from V2to 11/z '' long. Die cast aluminum body with tex-
tured grip minimizes operator fatigue. Large capacity, top
loading magazine with positive quick action latch makes load-
ing easy. Safety feature disables tool unless contact trip is
pressed against workpiece. Tapered nosepiece provides oper-
ator with greater visibility for precise fastener placement. Rigid
nosepiece reduces jamming. Quick-release
nose cover allows
for easy removal of jammed fasteners. The ¼" Crown Stapler
is excellent for furniture making, upholstery, cabinetry and
picture framing.
SPECIFICATIONS
Capacity ...............................
160 staples
Staple crown width ..............................
W'
Staple lengths
............................
V2to 1V2"
Staple size ....................
18 gauge (.049 x .040")
Operating pressure .......................
60-100 PSI
Air inlet ..................................
W' N.P.T.
Length .....................................
10W'
Height .......................................
9W'
Width .......................................
2W'
Weight ....................................
2.6 Ibs.
STAPLES
18333 ............................
¼" crown, W' long
18334 ............................
¼" crown, 3/4"long
18336 ............................
1/4"crown, 7/8"long
18371 ............................
¼" crown, 1" long
18372 ...........................
¼" crown, 1W' long
18373 ...........................
¼" crown, 1¼" long
18374 ...........................
1/4"crown, 1W' long
AIR SUPPLY
LINE
Refer to Figure 1 (page 3).
*
The air tool operates on compressed
air at pressures from
60 to 100 PSI.
*
Never exceed maximum pressure.
Air Delivery
Required:
0.71 SCFM @ 90 PSI
(30 shots per minute).
WARNING:
Keep hands and body away from discharge area
of tool when connecting air supply. Always disconnect tool
from air supply when servicing or adjusting tool and when tool
is not in use.
*
Air operated tools require clean, dry, lubricated com-
pressed air to ensure top performance,
low maintenance
and long life.
*
Dirt and abrasive materials present in all air lines will dam-
age tool O-rings, valves and cylinders.
*
Moisture will reduce tool performance and life if not
removed from compressed air.
*
A filter-regulator-lubricator
system is required and should
be located as close to tool as possible (see Fig. 1, page
3). A distance of less than 15 feet is recommended.
2
Advertisement
