Table Of Contents - Craftsman 113.198251 Operator's Manual

Table of Contents

Table Of Contents2
Safety Information3
Major Hazards3
Workpiece Kickback3
Kickback Followed By Blade Contact3
Wrong Way Feed4
Thrown Workpiece Chips And Blade Pieces4
Personal Safety5
Saw Safety5
Workpiece Support Safety6
Blade Safety6
Safety Labels On The Radial Arm Saw6
Putting Your Saw Together7
Unpacking/Set Up7
Parts Included8
Tools Required8
Information10
Model 113.198211 - Beginning The Cabinet11
Attaching Door14
Building The Leg Set15
Attaching Handwheel16
Mounting The Motor17
Mounting The Saw18
Attaching Trim Ledge And Trim Caps18
Location And Function Of Controls19
On/Off Switch19
Miter Lock19
Bevel Lock20
Swivel Lock21
Rip Lock21
Handwheel22
All Controls22
Alignment Of The Blade23
Adjusting Elevation23
Leveling Table Supports24
Mounting The Front Table26
Mounting Table Clamps27
Squaring Crosscut Travel28
Squaring Blade To Table For Crosscutting30
Squaring Blade To Fence31
Squaring Blade To Table For Ripping33
Making Blade Parallel To Table35
Installing Guard/Setting Spreader36
In-Rip Position37
Digital Display39
Installing The Battery40
Replacing The Battery40
Aligning Encoders40
Miter Encoder40
Bevel Encoder42
Setting Zero References43
In-Rip Reference43
Out-Rip Reference44
Electrical Connections45
Motor Specifications45
Power Supply45
Extension Cords46
Adapter For 2-Prong Receptacles46
Crosscutting47
Types Of Crosscut47
Safety Information For Crosscutting48
Blace Distance To Complete Crosscut48
Blade Guard, Anti-Kickback Pawls And Spreader49
Crosscutting Checklist50
Cutting Table And Fence Kerfs50
Making Table And Fence Kerfs For Crosscutting50
Makig Crosscuts52
Fence Position For Crosscut52
Repetitive Crosscuts53
Distance Needed To Complete Crosscut53
Ripping54
Saw Positions For Ripping54
When To Use In-Rip Or Out-Rip54
Workpiece Positioning For Ripping54
Safety Information For Ripping55
Kickback, Blade Contact Safety Sign View55
Kickback, Thrown Workpiece Safety Sign View55
Wrong Way Feed Safety Signs View56
Infeed And Ouffeed Ends Of Saw Blade View56
Blade Guard, Anfi-Kickback Pawls And Spreader57
Rip Cutting Checklist57
Making A Rip Cut Table Kerf58
Adjustment For Ripping58
Blade Guard Adjustment58
Blade Guard Position For Ripping58
Making Rip Cuts59
Anti-Kickback Pawls And Spreder Adjustments59
When To Use In-Rip And Out-Rip59
Hand And Body Position For Making An In-Rip Cut60
Bevel Ripping61
Dadoing61
Molding61
Edging61
Accessory Safety62
Arbor Shaft Position When Using Accessory Shaft62
Cutting Accessories63
Fences63
Push Stick63
Auxiliary Fence And Push Block64
Auxiliary Fence For Edging65
Push Block Dimensions65
Featherboard66
Attaching Auxiliary Board To Crooked Workpiece66
Recommended Accessories67
Lower Retractable Guard67
Glossary68
Helpful Hints69
Making A 4-Sided Frame69
Decimal Equivalent70
Motor71
Maintaining Your Saw72
Replacing Antikickback Pawls72
Cleaning72
Lubrication72
Swivel And Bevel Indeg Pins View73
Collapsed Bellows View73
Bearing Points Where Arm Attaches To Column Tube73
Adjustments For Wear74
Arm And Column75
Carriage Bearings75
Location Of Hex Head Tapping Screws75
Front Carriage Bearings View76
Location Of Hex Nut View76
Miter Lock - Unlocked View77
Location Of Hex Lock Nut View77
Location Of Hex Socket Cap Screw77
Troubleshooting78
Electronics Troubleshooting78
Motor Troubleshooting79
Saw Operations Troubleshooting81
Parts List For Craftsman 10" Electronic Raidal Saw Model Nos. 13.198211 And 113.19825184
Exploded View - Figure 184
Base And Columne Assembly Exploded View86
Yoke And Motor Assembly Exploded View88
Yoke Assembly Exploded View90
Motor Assembly Exploded View92
Arm Assembly Exploded View94
Guard Assembly Exploded View96
Table Assembly View97
23" Cabinet Assembly View (Model 113.198211 Only)98
Leg Set Exploded View (Model 113.198211 Only)99