Download Print this page

Craftsman 113.213090 Owner's Manual page 6

Motorized 10-inch bench model drill press with maximum developed 1/2 hp motor

Advertisement

ifi
_ m
motor spec Tca ons and electrica
requ
i_i !i_ i_i_i _
°
t i¸
reme
s
MOTOR SPECiFICATiONS
TNs dril! press is designed to use a 1725 RPM motor
only. Do not use any motor that runs faster than 1725
RPM It is wired for operation on 110-120 volts. 60 Hz.
alternating current,
WARNING:
TO
AVOID
INJURY
FROM
UNEX-
PECTED STARTUP, DO NOT USE BLOWER OR
WASHING MACHINE
MOTORS OR ANY MOTOR
WITH AN AUTOMATIC RESET OVERLOAD PRO-
TECTOR.
CONNECTING
TO POWER
SOURCE OUTLET
This machine must begrounded while _nuse to protect
the operator from electric shock.
Plug power cord Into a 110-!20V
properly grounded
type outlet protectea by a 15-amo dual element time
delay or Circuit breaker.
NOT ALL OUTLETS ARE PROPERLY GROUNDED.
IF YOU ARE NOT SURE THAT YOUR OUTLET, AS
PICTURED BELOW. iS PROPERLY
GROUNDED,
HAVE IT CHECKED BY A QUALIFIED ELECTRiCiAN.
WARNING: TO AVOID ELECTRIC SHOCK. DO NOT
TOUCH THE METAL
PRONGS
ON THE PLUG,
WHEN INSTALLING OR REMOVING THE PLUG TO
OR FROM THE OUTLET.
WARNING: FAILURETO PROPERLY GROUNDTHIS
POWER TOOL CAN CAUSE ELECTRICUTION
OR
SERIOUSSHOCK, PARTICULARLY WHEN USED IN
DAMP LOCATIONS. OR NEAR METAL PLUMBING.
IF SHOCKED, YOUR REACTION
COULD CAUSE
YOUR HANDS TO HIT THE CUTTING TOOL
IF POWER CORD IS WORN OR CUT, OR DAMAGED
IN ANY WAY, HAVE IT REPLACED IMMEDIATELY
TO AVOID SHOCK OR FIRE HAZARD.
This power tool is equipped with a 3-conductor
and grouna_ng type plug, approved
by Underwriters'
Laooratories and the Canadian Standards Association:
The grouna conductor has a green jacket and is at_
tached to the tool housing at one end and to the grour]d
prong in the attachment plug at the other end.
This plug requires a mat ng 3-conductor grounded type
outlet as shown.
If the outlet you are planning to use for this power tool
s of the two prong type, DO NOT REMOVE OR ALTER
THE GROUNDING
PRONG IN ANY MANNER. Use
an adapter as shown and always connect the grounding
tug to known ground.
It is recommended that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE orong outlet.
An adaoter as shown below is available for connecting
plugs to 2-pror_g receptacles.
WARNING:
THE GREEN
GROUNDING
LUG EX-
TENDING
FROM THE ADAPTER
MUST BE CON-
NECTED TO A PERMANENT
GROUND
SUCH AS
TO A PROPERLY GROUNDED
OUTLET BOX.
GROUNDING
LUG
SCREW
\
ADAPTER
3-PRONG
PLUG
\
GROUNDING
PRONG
has a plug that looks
NOTE: The adapter illustrated is for use only if you
alreaoy nave a properly grounded 2-prong receptacle,
Adapter is not allowed in Canada by the Canadian Elec-
trical Code.
The use of any extension cord will cause some loss of
0ower. To Keep this to a minimum and to prevent over-
neatmcj and motor bum-out, use the table below to
determine the minimum wire size (A W.G) extension
cord Use only 3 wire extension cords which have 3-
prong grounding
type plugs and 3-pote receptacles
which accept the tools ptug.
Extension Cord Length
Wire Size A.W.G.
0-25Feet
16
26-50Feet
!4
51-100 Feet
12

Advertisement

loading