Sharp DV-HR400S Operation Manual page 44

Recording to DVD
42
GB
2
Set a DVD-RW or DVD-R disc.
• When a new DVD-RW disc not
initialised yet is set, VR mode
initialising starts automatically. When
initialising is over, you can start
recording.
• When you want to re-initialise in Video
mode, select "DVD INITIALISE
(VIDEO)" screen (page 96).
• When you want to initialise in Video
mode from the beginning, select
"DVD AUTO INITIALISE" screen
(page 105).
3
Press Number buttons or CH ' /
" to select the channel to record.
4
Press REC MODE to select the
desired recording mode.
• The recording mode changes as
shown below each time the button is
pressed.
XP SP LP
• Recording mode set when "MNgg"
is selected is the recording mode set
on the "REC MODE SETTING" screen
(page 44).
5
Press Æ Æ Æ Æ Æ REC.
• Recording begins and REC icon is
displayed.
• To perform recording by operating the
controls on the Recorder, press the
Æ REC button on the DVD side (right).
• Æ REC on the DVD (right) side of the
Recorder is lit during recording.
6
Press REC PAUSE to pause
recording.
• Pause will not function during timer
recording.
• Æ REC on the DVD (right) side of the
Recorder blinks during Recording
Pause mode.
7
Press REC PAUSE to resume
recording.
8
Press REC STOP to stop
recording.
• To stop recording by operating the
controls on the Recorder, press the
REC STOP button on the DVD side
(right).
• "RECORDING DATA TO DISC." is
displayed on TV screen and record-
ing stops.
• Stop recording before you take out
the disc.
• Data is still written to the disc after recording
is stopped, and so you may be unable to
start the next recording immediately.
• Press ON SCREEN (under the cover) to
confirm remaining time of DVD or check
the counter display during recording.
• You cannot record programmes which
prohibit recording.
• Recording either stops or pauses automati-
cally in the following cases.
—Programme which prohibits recording is
—Unable to continue recording for some
• Timer recording cannot be performed
during direct recording. To perform timer
recording, stop direct recording before the
preset time for timer recording.
• Digital broadcast can only be recorded in
VR format to DVD-RW disc (CPRM
enabled).
You may not be able to record on disc
EP MNgg
edited by other recorder.
• If a disc edited by other DVD recorder has
more than 999 chapter markers, it cannot
be edited (or recorded) with this Recorder.
• If a disc edited by other DVD recorder has
added or erased scenes 51 times or more
per title or the disc is protected, it cannot
be edited (or recorded) with this Recorder.
About Recording to DVD in Video Mode
• In case you are recording to DVD in Video
mode and recording stops due to power
failure etc., recorded contents a few
minutes before the stop may not be
recorded.
• To record bilingual broadcast in Video
format, you should select which audio
channel to record out of L CH and R CH
REC
("BILINGUAL SETTING", Page 104.)
• For details on limitation during recording
(dubbing) in Video mode, see also pages
59, 60.
Inserting Chapter Markers
Manually during Recording
Press CHAPTER MARK.
• "RECORDED CHAPTER MARKER." is
displayed and chapter marker is recorded.
• You can only record chapter markers
manually when recording to DVD-RW (VR
mode).
• You cannot record chapter markers
manually when recording to DVD-RW
(Video mode) or DVD-R, or during Simulta-
neous Recording/Playback.
Setting Record End Time
during Direct Recording
• You can set record end time during direct
recording to DVD. For details see "Setting
the Record End Time during Direct
Recording (Simple Recording Timer)" on
page 40.
NOTE
on air.
reason.