Adjust The Image - Epson PowerLite 715C Quick Setup

Adjust the image

If you see a blank screen
Note:
see the instructions in the box below.
1
Rotate the focus ring to sharpen the image.
Rotate the lens ring if you need to reduce or enlarge
2
the image. (You can also move the projector closer to
or farther from the screen.)
If You See a Blank Screen
If you see a blank screen or the No Signal message
after turning on your laptop, check the following:
Make sure the power light is green and
not flashing and the lens cover is off.
Try turning off the laptop and restarting it.
If you've connected a computer and video source, you may need to
press the Source button on top of the projector. (Allow a few
seconds for the projector to sync up after pressing it.)
Make sure the computer cable is securely connected at both ends.
If you're using a Windows laptop:
Hold down the Fn key on your keyboard and press the function
key that lets you display on an external monitor. It may have an
icon such as , or it may be labelled CRT/LCD. (Allow a few
seconds for the projector to sync up after pressing it.)
You might need to use the Display utility in the Control Panel
to enable both the LCD screen and external monitor port.
If you're using a Macintosh:
1. From the Apple menu, select Control Panels, then click Monitors
and Sound.
2. Click the Arrange icon.
3. Drag one monitor icon on top of the other. This lets you display
on the projector screen as well as the LCD screen.
If this option isn't available, you may need to select one of the
Simulscan resolution settings:
4. Click the Monitor icon.
5. Select a Simulscan resolution. (Allow a few seconds for the
projector to sync up after making the selection.)
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.
Copyright © 2001 by Epson America, Inc.
,
No signal
keystone button
lens ring
focus ring
No signal
EPSON PowerLite 505c/715c
Raise the image as needed. To do this, pull up the blue foot
3
release levers and lift the front of the projector. Once the
image is positioned where you want it, release the levers
to lock the feet in position.
4 If your image looks like
off to one side of the screen, at an angle. Move it directly in
front of the center of the screen, facing the screen squarely.
If your image looks like
5
Keystone button on top of the projector to correct the shape
of the image.
Presenting Without A Computer
EasyMP lets you run your presentation from the projector. Simply
®
convert your PowerPoint file into a "scenario" with the
EMP SlideMaker software on your computer. Then download
your scenario to the projector's memory card.
If your scenario is set to autorun, it will start
when you turn on the projector. You can present
it with the remote control.
1. Make sure the remote control has batteries.
2. Push up the switch on the side of the
remote control to turn it on.
Press Enter to display the next slide.
Press Esc to display the previous slide.
If your scenario is not set to autorun,
start it by following these steps:
1. Press the EasyMP button on the remote control.
You see the EasyMP main screen.
2. Use the Enter button on the remote control
to highlight your scenario (SIT) file.
3. Press Enter. In a moment, your presentation begins.
Press Enter to display the next slide.
Press Esc to display the previous slide.
4. To exit, press the EasyMP button on the remote control.
You see a confirmation message.
5. Press Enter to exit. You return to the EasyMP main screen.
See your User's Guide for more information about
presenting without a computer.
or , you've placed the projector
or , press the + or – side of the
ON/OFF switch
Power Power
Freeze Freeze
A/V Mute A/V Mute
R/C ON R/C ON
E-Zoom E-Zoom OFF OFF
3 3
Enter Enter
Esc
Esc
Menu Help
EasyMP
Comp 1
Video
Auto Resize
P in P
- Volume +
CPD-11737