Table of Contents
Advertisement
Quick Links
LIBERTY
www.regency-fi re.com
WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life.
FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other appliance.
Installation and service must be performed by a qualifi ed
installer, service agency or the gas supplier.
Tested by:
918-722a
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
L676-1 Gas Fireplace
™
MODELS: L676-NG1 Natural Gas L676-LP1 Propane
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Owners &
Installation Manual
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:
do not use any phone in your
building.
Immediately call your gas supplier
from a neighbour's phone. Follow
the gas supplier's instructions.
If you cannot reach your gas
supplier, call the fi re department.
02/09/09
Advertisement
Table of Contents
Related Manuals for Regency Liberty L676-NG1
Summary of Contents for Regency Liberty L676-NG1
- Page 1 Owners & LIBERTY L676-1 Gas Fireplace ™ Installation Manual www.regency-fi re.com MODELS: L676-NG1 Natural Gas L676-LP1 Propane WARNING: FOR YOUR SAFETY If the information in these instructions are not followed exactly, What to do if you smell gas: a fi re or explosion may result causing property damage, Do not try to light any appliance personal injury or loss of life.
- Page 2 WARNING HOT GLASS WILL CAUSE BURNS DO NOT TOUCH GLASS UNTIL COOLED NEVER ALLOW CHILDREN TO TOUCH GLASS CHILDREN AND ADULTS SHOULD BE ALERTED TO THE HAZARDS OF HIGH SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND SHOULD STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.
-
Page 3: Manufactured Mobile Home Requirements
To the New Owner: Congratulations! You are the owner of a state-of-the-art Gas Fireplace by REGENCY . The L676-1 has been ® designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch. -
Page 4: Table Of Contents
WARRANTY Allowable Vertical Terminations ......22 Unit Installation with Horizontal Termination ....23 The Warranty: Limited Lifetime ........47 Unit Installation with Vertical Termination ....24 Unit Installation ............25 Horizontal Termination .........25 with Flex Vent System .........25 Regency L676-1 Direct Vent Gas Fireplace ®... -
Page 5: Safety Label
Gas Fireplace. We have printed a copy of the contents here for your review. The safety label is located on the left hand side of the unit behind the mesh screen. NOTE: Regency units are constantly being ® improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. -
Page 6: Requirements
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 7: Unit Dimensions
UNIT DIMENSIONS Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 8: Installation
11) Under no circumstances should this OR CLOTHING IGNITION. appliance be modifi ed. Parts that have to be 8) Test the pilot (Refer to "Pilot Adjustment" removed for servicing should be replaced section). prior to operating this appliance. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 9: Manufactured Mobile Home Additional Requirements
The appliance must be installed on a metal The HeatWave Duct Kit has different or wood panel extending the full width and clearance and framing requirements, depth of the appliance. check the HeatWave manual for details. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 10: Clearances
It is of greatest importance that this position for ease of conversion. See "Conversion fi replace and vent system be installed only in from NG to LP" section for instructions. accordance with these instructions. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 11: Mantel Clearances
Note: A non-combustible mantel may be installed at a lower height if the framing is made of metal studs covered with a non-combustible board. Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour. MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram: Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 12: Framing & Finishing
If converting this unit to LP, it is highly recommened the conversion be done BEFORE the unit is slid into position for ease of conversion. See "Conversion from NG to LP" section for instructions. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 13: Unit Assembly Prior To Installation
(see diagram below). Install the facing material up to the outside edge (when facing the unit) of the fi nishing template. This template may be discarded after the facing material has been installed. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 14: Vent Restrictor Position
5) Adjust the vent restrictor plate to the required Center it between the 2 relief doors (see vent restrictor position as per the diagrams above diagram), secure with 2 self tapping Right Side Rod with Screen Removed shown. screws provided. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 15: Exterior Vent Termination Requirements
* Clearance in accordance with local installation codes and the requirements of the gas supplier 3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly 3 feet (91cm) above - if within 10 feet (3m) horizontally Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 16: Venting Arrangements
INSTALLATION VENTING ARRANGEMENTS HORIZONTAL TERMINATION (FLEX) Regency Direct Vent System ® These venting systems, in combination with the L676-1, have been tested and listed as a direct vent system by Warnock Hersey. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram from the "Exterior Vent Termination Locations" section. -
Page 17: Rigid Pipe Venting Systems
Direct Vent Pro and Selkirk Direct-Temp. AstroCap XL is a proprietary trademark of FPI Fireplace Products International Ltd. Dura-Vent® and Direct Vent GS are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 18: 5" X 8" Rigid Pipe Cross Reference Chart
INSTALLATION 5” X 8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI. Regency ® L676-1 Direct Vent Gas Fireplace... - Page 19 INSTALLATION Regency ® L676-1 Direct Vent Gas Fireplace...
-
Page 20: Venting Arrangements
Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting of Set 1 to Set 2 or Set 4 if required. Note: Regency Direct Vent System (Flex) is only approved for horizontal terminations. - Page 21 5' Min. 4' Max. 10' Min. 7' Max. between 90 elbows is 6' Min. 6' Max. 11' Min. 9' Max. required. VENT RESTRICTOR SETTING: Vent restrictor factory set at Set 1, no adjustment required. Regency ® L676-1 Direct Vent Gas Fireplace...
- Page 22 Please note min. 1 foot 5' Min. 6' Max. 8' Min. between 90 elbows is 6' Min. 8' Max. 9' Min. required. VENT RESTRICTOR SETTING: Vent restrictor factory set at Set 1, no adjustment required. Regency ® L676-1 Direct Vent Gas Fireplace...
-
Page 23: Venting Arrangements
Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting of Set 1 to Set 2 or Set 3 if required. Note: Must use optional fl ue adapter when using Rigid Pipe (Part # 770-994). Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 24: Unit Installation With Horizontal Termination
(supplied) to every inner pipe connection. Failure to do so may result in drafting or performance issues not covered under warranty. Silicone (red RTV) is optional. Diagram 7 Diagram 1 Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 25: Unit Installation With Vertical Termination
Diagram 5 or Diagram 3 local codes. Note that for steep roof pitches, the vertical height must be increased. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 26: Unit Installation
1-3/8"(35mm) and fasten with the 3 screws. NOTE: Horizontal sections must be sup- ported at intervals not exceeding 3 feet (0.9 meter). (Flame picture and performance will be affected by sags in the liner). Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 27: High Elevation
(it does not have to be touching the Minimum Input 25,000 Btu/h 25,000 burner). (7.33 kW) Btu/h (7.33 kW) Note: If you have an incorrect fl ame pattern, contact your Regency ® dealer for Maxiumm Input 31,500 Btu/h 31,500 further instructions. (9.23 kW) Btu/h (9.23 kW) -
Page 28: Aeration Adjustment
Wiring errors can cause improper and dangerous operation. NOTE: The #8 ground lug is located on the outer left side of the unit. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 29: Conversion From Ng To Lp
fi rebox. the log tray by undoing the 2 screws. Burner Orifi ce Cover Plate Latch Location Latch 5) Remove the grate by undoing the 3 screws. Right Side Rod with Screen Removed Grate Regency ® L676-1 Direct Vent Gas Fireplace... - Page 30 Check the inlet and outlet pressures. c) Check operation of fl ame control using the remote control. d) Check for proper fl ame appearance. Installer Notice: This instructions must be left with the appliance. Regency ® L676-1 Direct Vent Gas Fireplace...
-
Page 31: Brick Panel Installation
Screw 3) Remove the glass door. a. Release the 2 door latches on the left and right side at the top of the fi rebox. L676-1 L900-1 Diagram 7 Diagram 4 Latch Location Regency ® L676-1 Direct Vent Gas Fireplace... - Page 32 5 (see Diagram 12). Back of Front of Unit Unit Diagram 13 10) FOR L676-1 UNITS ONLY: Re-install the burner orifi ce cover plate. Top Brick Panel Diagram 10 Diagram 14 Regency ® L676-1 Direct Vent Gas Fireplace...
-
Page 33: Log Set Installation
The reference numbers (i.e. A) are molded into the rear of each log. 1) Carefully remove the logs from it's packaging and unwrap them. The logs are fragile, handle with care - do not force into position. Regency ® L676-1 Direct Vent Gas Fireplace... - Page 34 5) Fit log A into the pins on the log tray. 7) Fit log E into the pin at the center of log A. 6) Fit log D into the pin on the far left side of log A. Regency ® L676-1 Direct Vent Gas Fireplace...
- Page 35 10) Fit log F into the pin on the far right side of log A. Rest the 2 ends of log F on the landings on log C. 1st Grate Post 2nd Grate Post 9) Rest the notch on the underside log C onto the 4th grate post. 4th Grate Post Regency ® L676-1 Direct Vent Gas Fireplace...
- Page 36 INSTALLATION Completed Log Set Installation Regency ® L676-1 Direct Vent Gas Fireplace...
-
Page 37: Mesh Pull Screen Installation
5) Spread the mesh evenly along the rod's to cover the glass door. Inside top view of Firebox Ensure the mesh goes around the curved end of the rod's as well. Completed Mesh Pull Screen Installation Outer Most Bracket Hole Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 38: Optional Andiron Installation
5) For the right side, slide the andiron bracket over the 4th grate post. 4th grate post. 6) Reinstall glass door and mesh. 6) Reinstall glass door and mesh. Final Installation L900-1 Final Installation L676-1 Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 39: Operating Instructions
"ON" button. The receiver will beep 4 times to indicate the remote control's command has been accepted and sets to the particular code of that remote control. Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 40: Normal Operating Sounds Of Gas Appliances
3) Turn off all electric power to the appliance if service is to be performed. You may shut off the pilot during prolonged non use periods to conserve fuel. DO NOT REMOVE THIS INSTRUCTION PLATE 918-583 Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 41: Maintenance
Wall Straps, paint and should only be refi nished with heat * Care must be taken to avoid breakage of the or plumbers' tape for rigidity. resistant paint. Regency ® uses StoveBright glass. Paint - Metallic Black #6309. -
Page 42: Dc Spark Box Battery Replacement
3) Remove AA battery and replace with a new one. 4) Re-install battery cover on DC Spark Box. 5) Spread the mesh along the rod ensuring that it goes around the curved end of the rod. DC Spark Box Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 43: Valve Tray Replacement
Place the door on a soft surface to prevent scratching. 10) Remove the rear log stand by removing the 4 screws. 5) Remove the log set. Rear Log Stand Front Cover Plate Right Side Pin Shown Regency ® L676-1 Direct Vent Gas Fireplace... - Page 44 28) Re-install the front cover plate 29) Re-install the mesh screen. DC Spark Box 30) Check the inlet and outlet pressures. 31) Check operation of fl ame control. 32) Check for proper fl ame appearance. Regency ® L676-1 Direct Vent Gas Fireplace...
-
Page 45: Parts List
Gas Line Screen Plate * Not available as a replacement part. 20) 522-901 Brick Panel Set - Standard Brown 522-902 Brick Panel Set - Standard Red Left Side Panel Top Panel Back Panel Right Side Panel Regency ® L676-1 Direct Vent Gas Fireplace... - Page 46 PARTS LIST Regency ® L676-1 Direct Vent Gas Fireplace...
-
Page 47: Burner & Log Assembly
910-008 Pilot Assembly - NG 910-009 Pilot Assembly - LP 904-689 NG - Orifi ce #33 904-645 LP - Orifi ce #51 910-073 Spark Generator Battery Holder 910-074 Spark Generator Switch c/w Wire Regency ® L676-1 Direct Vent Gas Fireplace... -
Page 48: Warranty
It is the general practice of FPI to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to FPI and evaluated for manufacturer defect. The authorized selling dealer is responsible for all in-fi eld service work carried out on your Regency product. FPI will not be liable for results or costs of workmanship from ®... - Page 49 Phone #: ___________________________________________________________ Date Installed: ______________________________________________________ Serial No.: __________________________________________________________ Regency, Liberty, AstroCap, HeatWave, Heat Release and FireWizard are trademarks of FPI Fireplace Products International Ltd. © Copyright 2009, FPI Fireplace Products International Ltd. All rights reserved. Printed in Canada Regency L676-1 Direct Vent Gas Fireplace ®...