Basic Drill Press Operation; Installingdnlls - Craftsman 113.213170 Owner's Manual

basic drill press operation
Follow the following mstructlons for operating your drdl
press tO get the best results and to m_mmize the likeli-
hood of personal inlury
WARNING: FOR YOUR OWN SAFETY, ALWAYS
OBSERVE THE SAFETY PRECAUTIONS HERE AND
ON PAGES 2, 3, AND 4.
f. Protection: Eyes, Hands, Face, Ears and Body
WARNING: TO AVOID BEING PULLED INTO
THE SPINNING TOOL --
a,
b.
Co
do
1, Do NOT wear:
- gloves
- necktie
- loose clothing
-- jewelry
2, Do tie back long hair
If any part of your drill press is missing, malfunc-
tioning, has been damaged or broken.., such
as the motor switch, or other operating control,
a safety device or the power cord.., cease
operating immediately until the particular part
is properly repaired or replaced.
Never place your fingers in a position where
they could contact the drill or other cutting tool
if the workpiece should unexpectedly shift or
your hand should slip.
To avoid injury from parts thrown by the spring,
follow instructions exactly as given and shown
in adjusting spring tension of quill.
To prevent the workpiece from being torn from
your hands, spinning of the tool, shattering the
tool or being thrown, always properly support
your work so it won't shift or bind on the tool:
-- Always position BACKUP MATERIAL (use
beneath the workpiece) to contact the left
side of the column.
-- Whenever possible, position the WORK-
PIECE to contact the left side of the col-
umn-if it is too short or the table is tilted,
clamp solidly to the table, use table slots or
clamping ledge around the-outside edge of
the table.
-- When using a drill press VICE, always fasten
it to the table.
,
- Never do any wQrk 'FREEHAND" (hand-
holding wor&piece rather than supportIng it
on the tableL except when polishing.
- Securely lock Head and Support to Column,
Table Arm tO support, and Table to Table
Arm before operating drill press.
- Never move the Head or Table while the
tool is running
-- Before starting the operation, jog the motor
switch to make sure the drill or other cutting
tool does not wobble or cause vibration.
-- If a workpiece overhangs the table such taht
it wilt fall or tip if not held. clamp it to the
table or provide auxiliary support.
--Use fixtures for unusual operations to
adequately hold, guide and position work-
piece,
-- Use the SPINDLE SPEED recommended
for the specific operation and workpiece ma-
terial-check the panel on the left side of
the head for drilling information; for acces-
sories, refer to the instructions provided with
the accessories.
f. Never climb on the drill press Table, it could
break or pullthe entire drill press down on you.
g. Turn the motor Switch Off and put away the
Switch Key when leaving the drill press.
h. To avoid injury from thrown work or tool contact,
do NOT perform layout, assembly, or setup
work on the table while the cutting tool is rotat-
ing.
Use only accessories designed for this drill
press to avoid serious injury from thrown bro-
ken parts or work pieces. ,
a. Holesaws must NEVER be operated on this drill
press at a speed greater than 400 RPM.
b. Drum sanders must NEVER be operated on
this drill press at a speed greater than 1800
RPM.
c. Do not install or use any drill that exceeds 7" in
length or extends 6" below the chuck jaws. They
can suddenly bend' outward or break.
d. Do not use wire wheels, router bits, shaper cut-
ters, circle (fly) cutters or rotary planers on the
drill press.
INSTALLING DRILLS IN CHUCK
With the switch off and the key removed, insert drill
into chuck far enough to obtain maximum GRIPPING
of the CHUCK JAWS... the jaws are approx. 1" long.
When using a small drill do not insert it so far that the
jaws touch the flutes (spiral grooves) of the drill.
Make sure that the drill is CENTERED in the chuck
before tightening the chuck with the key.
Tighten the drill sufficiently, so that it does not SLIP
while drilling.
Turn the chuck key clockwise to tighten--coun-
terclockwise to loosen.
JAWS
23