Sign In
Upload
Download
Table of Contents
Contents
Add to my manuals
Delete from my manuals
Share
URL of this page:
HTML Link:
Bookmark this page
Add
Manual will be automatically added to "My Manuals"
Print this page
×
Bookmark added
×
Added to my manuals
Manuals
Brands
Craftsman Manuals
Saw
113.19770
Owner's manual
Alignment Of Spreader For Ripping; Fence Locations; Install Blade Guard; Check And Adjust The Spreader As Follows - Craftsman 113.19770 Owner's Manual
10-inch radial saw
Hide thumbs
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
Table Of Contents
45
page
of
45
Go
/
45
Contents
Table of Contents
Troubleshooting
Bookmarks
Table of Contents
Advertisement
assembly
and alignment
ALIGNMENT
OF SPREADER
FOR RIPPING.
WARNING:
NEVER
POSITION
THE
GUARD
OR
ANTI
KICKBACK
ASSEMBLY
WITH
POWER
ON;
NOR
POSITION
ANTIKICKBACK
PAWLS
BY
GRASPING
PAWLS
OR SPREADER.
2.
Install
Blade Guard.
a.
Sight
(visually)
to
check
for
proper
alignment
of
spreader
with
saw blade
as shown.
If the spreader
is
not aligned,
adjust
it as follows:
(1} Loosen
two
hex
nuts,
one
on
each
side
of
spreader.
(2) Rotate
hex nuts
with
fingers
until
the spreader
is directly
in line with
saw blade.
(3_ Tighten
both
hex nuts firmly.
)
/-_
HEX NU
_x_ PREADER
_--WINO
SCREW
/
3.
Check and Adjust
the spreader
as follows:
a.
Loosen
the
antikickback
spreader
adjusting
wing
screw
and with
the "tab"
position
the antikickback
and spreader
assembly
near the bottom
of the blade
and tighten.
OUTSIDE
VIEW
ANTIKICKBACK,
SPREADER
ADJUSTING
WING
SCREW
TAB
ANTIKICKBACK
PAWLS
INSIDE
VIEW
FENCE
LOCATIONS
Position
(A)
is used for
most
cutoff
and narrow
ripping
operations.
Position
(B)
is
used
for
maximum
width
ripping.
Positio
. (C) is used to achieve
maximum
crosscut
capacity
in thin work.
Now
that
you
have assembled
and aligned
your
saw, you
are ready
to proceed
with
operating
controls
section
of this
manual.
Refer
to trouble
shooting
section
if saw does not
perform
satisfactorily
or any problems
should
surface
after
using the saw.
B
CA
r-i
n
I"-1
fh_lq__
_------I
,-4
I
19
Table of
Contents
Previous
Page
Next
Page
1
...
16
17
18
19
20
21
22
23
Show Quick Links
Quick Links:
Instructions for Power
Motor Specifications
Assembly and Alignment
Basic Saw Operations
Repair Parts
Hide quick links:
Permanently
Temporary
Cancel
Advertisement
Table of Contents
Related Manuals for Craftsman 113.19770
Saw Craftsman 113.19771 Owner's Manual
Io-inch radial saw (45 pages)
Saw Craftsman 113.19771 Owner's Manual
Io-inch radial saw (45 pages)
Saw CRAFTSMAN 113.197752 Owner's Manual
1o-inch radial saw (43 pages)
Saw CRAFTSMAN 113.19760 Owner's Manual
1o-inch radial saw (45 pages)
Saw Craftsman 9-29012 Owner's Manual
10-inch radial saw guard kit (20 pages)
Saw CRAFTSMAN 113.197110 Operator's Manual
10-inch radial saw (89 pages)
Saw CRAFTSMAN 113.19761 Owner's Manual
10-inch radial saw (45 pages)
Saw CRAFTSMAN 113.197250 Operator's Manual
1o" electronic radial saw with 23" cabinet and 1 door; 10" electronic radial saw with leg set (105 pages)
Saw Craftsman 113.197511 Owner's Manual
10-1nch radial saw (104 pages)
Saw Craftsman 113.198310 Owner's Manual
Io-inch radial saw (57 pages)
Saw Craftsman 113.198210 Owner's Manual
10" electronic radial saw with 23" cabinet and 1 door (69 pages)
Saw Craftsman 113.196421 Owner's Manual
10-inch radial saw (81 pages)
Saw CRAFTSMAN 113.196120 Owner's Manual
10-inch radial saw (81 pages)
Saw CRAFTSMAN 113.196380 Owner's Manual
10-1nch radial saw (81 pages)
Saw CRAFTSMAN 113.198411 Operator's Manual
10-inch deluxe electronic radial saw (121 pages)
Saw CRAFTSMAN 113.198110 Owner's Manual
10-inch radial saw with leg set (57 pages)
Related Content for Craftsman 113.19770
315.228310 Checking Rip Fence And Blade Alignment
Craftsman 315.228310
141.142580 Checking The Alignment
Craftsman 141.142580
315.272350 Checking Rip Fence And Blade Alignment
Craftsman 315.272350
315.228110 To Check The Alignment Of The Rip Fence To The Blade
Craftsman 315.228110
137,248830 Bevel Ripping
Craftsman 137,248830
113.19771 Assembly And Alignment
Craftsman 113.19771
113.23100 Alignment Of Anti-Kickback And Spreader Assembly, For Ripping
CRAFTSMAN 113.23100
113.23111 Alignment Of Anti-Kickback And Spreader Assembly, For Ripping
CRAFTSMAN 113.23111
113.19760 Alignment Of Spreader For Ripping
CRAFTSMAN 113.19760
113.19771 Alignment Of Spreader For Ripping
Craftsman 113.19771
113.29461 Positioning Sawdust Chute, And Anti-Kickback And Spreader Assembly, For Ripping
CRAFTSMAN 113.29461
113.29411 Ripping
Craftsman 113.29411
315.221850 To Check Miter Plate Alignment
Craftsman 315.221850
ACCRA-ARM 113.29402 In-Ripping
Craftsman ACCRA-ARM 113.29402
Accra-Arm 113.29440 Ripping
Craftsman Accra-Arm 113.29440
137.415030 Ripping
Craftsman 137.415030
This manual is also suitable for:
113.197750
Table of Contents
Print
Rename the bookmark
Delete bookmark?
Delete from my manuals?
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL