Table Of Contents; Unpacking And Checking Contents - Craftsman 113.225941 Owner's Manual

: .......... ::i:i:/i ¸¸ :: : ;: i :/::::i:i,i_ jl _: ! : i,:i_i:::: i :: :? : :, : • • •: • -•
i_:..... -::i_i_i.i. i i installing the Abrasive Belt-. ...................................... 4
Tensioning and Tracking.: .......................................... 14
._:!:i_ _ :_:_: _.i;_::_ _, ,:.::.:.. 2: Installing Belt D ust Trap ............................................ 15
i':':i:iiii:::i:::i!i:_'!:::,". :: Installing Backstop:.. .....:........................................... 16
Getting to Know Your Belt and Disc Sander ................. 16
Safety: Instructions for Belt and Disc Sander ................ 19
i !:: Hands, ....
Before Using the Sander: .......................................... 19
i:: 3: : When 'Installing OrMoving the Sander: .................... 19
: : ::
BeforeEach Use:....................................... 19
: Whenever Sander:iisRUnning :_i_i':i'=_i':::_i:'':i_:i_:_::'_''''--:--'4 Plan Ahead to Protect Your Eyes, Hands,
: i Face and Ears: ....................................................... 19
Precauti0ns t0 Take When Sanding Metais;,. i.i ..,.i .i.... i._4 Basic Sander Operation ............................................... 20
Precauti0nsto Take: when Sanding Whenever Sander is Running: .................................. 20
Motor Specifications and Electrical Requirements ......... 5
Connecting to Power Supply Outlet. ............................ 5
Table of Contents .............. i.i.._., i ..................................... 6
Unpacking and Checking Contents ............................. 6
ToolsNeeded .... :: .......... _ ............................. :_ . .............. 6
Loose Parts...: ..... ..ii. ................................................... 6
U npackin g ................................................................... 6
TableofLoose Parts ....................................................... 7
Assembly.... .................................................................... 7
Assembling SteelLegs ................................................ 8
When Installing Or Moving the Sander........................ 8
MountingBeltAnd DiscSander On Legset................. 9
Installing V-Beltand Switch......................................... 9
Installing Sanding Disc and Dust Trap.... , .................. 10
InStalling Motor,V-Belt and BeltGuard ..................... 11
On-OFF Switch..... ........... i... ...................................... 12
Installing Work Table................................................. 14
Before Leaving the Sander: ...................................... 20
Precautions to Take When Sanding Metals .................. 20
Precautions to Take When Sanding Paint .................... 20
Surface Finishing on the Abrasive Belt ..................... 21
End Finishing on the Abrasive Belt ........................... 21
Finishing Curved Edges on the Abrasive Belt ........... 21
Finishing Small End Surfaces and Curved Edges
on the Abrasive Disc ............................................. 22
Maintenance ................................................................. 22
Motor Maintenance and Lubrication .......................... 22
Lubrication ............................................ 22
Recommended Accessories . ............................... 23
Troubleshooting .......................................... 23
RepairParts............................................ 25
Motor Connections ....................................... 30
Unpacking and Checking Contents
Tools Needed
318" Wrench
7116" Wrench
9116" Wrench
3/4" Wrench
Medium
Screwdriver
#2 Phillips
Screwdriver
Combination Square
Combination Square Must be True
Draw Light
Line on Board Straight Edge of
Along this_ _/Board 314" Thick
"" _I_L_ This Edge Must be
Perfectly Straight
Should be no Gap or Overlap when Square
is Flipped Over in Dotted Position
Unpacking
Separate all parts from packing materials and check
each item with illustration and "Table of Loose Parts."
NOTE: Before discarding any packing material make cer-
tain all items are accounted for.
WARNING: To avoid injury, if any parts are missing,
do not attempt to assemble the belt and disc
sander, plug in the power cord, or turn the switch
on until the missing parts are obtained and
installed correctly,
WARNING: For your own safety, never connect
plug to power source outlet, or insert switch key
until all assembly steps are complete and until you
have read and understood the entire owners man-
ual.