Advertisement
Serial
Number ...........................
Model and serial
number may be found
on the right side
of the base.
You should record both
model and serial number
in a safe place for
future use.
CAUTION:
Read
GENERAL
and
ADDITIONAL
SAFETY
INSTRUCTaONS
carefu|ly
I INCH
SANDER
. assembly
® operating
® repair parts
GRINDER
Sold by SEARS,
Part No, 68038
ROEBUCK
AND
CO.,
Chicago,
I L.
60684
U.S.A.
Advertisement
Table of Contents
Related Manuals for Craftsman 113.22560
Summary of Contents for Craftsman 113.22560
- Page 1 Serial Number ......Model and serial number may be found on the right side of the base. You should record both model and serial number in a safe place for future use. I INCH CAUTION: GRINDER SANDER Read GENERAL ADDITIONAL .
- Page 2 "•,; ..L • ,- q•,i ¸ - •, • • •• FULLONE YEAR WARRANTY ON CRAFTSMAN 1 INCH SANDER/GRINDER to a defect state. SEARS. ROEBUCK AND CO., Sears Tower. 8S0 41-3. Chicago, IL 60684 ,, ,, general safety...
-
Page 3: Tools Needed
WARNING: 8, Do Not Grind or Polish Magnesium... because it could YOUR SAFETY, catch on fire. ATTEMPT OPERATE YOUR SANDER/GRINDER UNTIL IT IS COMPLETELY ASSEMBLED ACCORDING Note and follow Safety Instructions that appear on the INSTRUCTIONS, THAT belt guard. UNDERSTAND FOLLOWING (SEE CONTENTS... -
Page 4: Conn Ecting To: Power Source O Utlet
PECm FICATIO NS LI:REQUi R EM ENTS WARNING: PROPERLY GROUNDED THIS POWER TOOL CAN INCUR THE POTENTIAL HAZARD The:AC m0tor is a Split Phase nomreversible type, with the ELECTRICAL SHOCK; PARTICULARLY WHEN following specifications -_ = USED DAMP LOCATIONS,/ PROXIMITY Horsepower ......... -
Page 5: I Nstalli Ng Abrasive
ASSEMBLY PUSH DOWN Your Craftsman Sander/Grinder is shipped complete including motor, The Disc Sanding attachment Miter Gauge are optional accessories. WARNING: YOUR SAFETY, NEVER REAR IDLER CONNECT PLUG TO POWER SOURCE OUTLET UNTIL ALL ASSEMBLY STEPS ARE COMPLETED. arm is spring... - Page 6 UB SANDER/GRINDER UPPER :::.: TRACKING SCREW IPPER GUARD /UPPER WHEEL "'-^o,_W LOWER _""_ :_ 4_"r:..__ h',_'lft .-.--TRACKING SCREW 0,o, 0c,o,,o00,o,,,0 o,o a0 0 <o< ..TABLE LOCK locks:table in place. Use a square or [_//\ "._I /ARRAS VE BELT TRACKING SCREWS are adjusted to track...
- Page 7 GRINDING METAL Move the workpiece across the belt. If the workpiece becomes too hot to handle, quench it in cold ware r. Never push a sharp corner of the workpiece rapidly against the belt because the belt could tear. INSIDE WORK BELT ON BOTH SIDES...
-
Page 8: Maintenance
k ¸ SHARPENING N_ON 1. Adjust table, to proper angular position for: intended BACK OF WOOD operation. Cock securely. 2_ When _sharpening short: cutting tools such as wood chisels; it wii[ be neceSsaW 1_oclamp a piece of wood to: the table. 3. - Page 9 RECOMMENDED ACCESSORIES DISC SANDING ATTACHMENT ....9-22563 STEEL STAND ......9-22219 POWER TOOL KNOW HOW "HANDBOOKS" MITER GAUGE (FOR USE WITH 9-22563) ..9-22574 TABLE SAW ......9-2918 ABRASIVE BE LTS 1" x 42" RADIAL SAW ......9-2917 FINE ........9-26056 MEDIUM .......
- Page 11 r,.O :<CO "-_ co .'Z_ '_-" X _'-... _ ._-.. .£ > "a 0"_ O0 0'_ 0 "o ..z n" 00 rr" -- -J rr" Ze_x _N-_ o.-__ _ -o__o >':...
- Page 12 1 UNCH SANDER GRINDER SERVICE that have purchased your 1-inch sander grinder, should a need ever exist for repair or service, simply contact any Sears Service Center and most Sears, Roebuck and Co. stores. Be sure to provide all pertinent facts when you catl or visit.