To Cancel Surround Mode - JVC RX-5022VSL Instructions Manual

Creating Realistic Sound Fields
3 Press SOUND.
The 10 keys are activated for sound adjustments.
4 Press TEST to check if you can hear the
sounds through all the speakers at the
equal level.
%
TEST
"TEST TONE L" starts flashing on the display, and a test tone
comes out of the speakers in the following order:
i__ TEST TONE L .__ TEST TONE C.__ TEST TONE R
(Left front speaker) (Center speaker) (Right front speaker) 1
J
TEST TONE LS ,_ TEST TONE RS,_
(Left rear speaker) (Right rear speaker)
Notes:
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when "CNTR SP"
is set to "NONE."
• No test tone comes out of the rear speakers when "REAR SP"
is set to "NONE."
5 Adjust the speaker output levels
(-10 to +10).
Adjust the center speaker and rear speakers levels
%/
comparing to the sound from the front speakers. _- REAR. L+
• TO adjust the center speaker level, press _ _
CENTER +/-. _>
• To adjust the left rear speaker level, press
-- REAR-R+
REAR.L +/
• To adjust the right rear speaker level, press
REAR•R +/-.
%/
-- CENTER+
6 Press TEST again to stop the test
TEST
tone.
On the front
panel:
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So make adjustments while listening to
the sound of the source played back.
Setting the analog or digital input mode for the
source you like to listen and start playing.
When playing back software encoded with Dolby Digital and
DTS Digital Surround, select the digital input mode (see page
11).
2 Press SURROUND ON/OFF to
activate Surround mode.
Each time you press the button, Surround
mode turns on and off alternately.
SURROUND ON/OFF
If you are playing back software encoded with Dolby Digital
multichannel, "DOLBY DIGITAL" is selected.
If you are playing back software encoded with DTS Digital
Surround, "DTS SURROUND" is selected.
If you are playing back any software other
than above, you can select "PL II MUSIC"
or "PL II MOVIE" according to the source
by pressing SURROUND MODE. (rln PRO
LOGIC II indicator lights up on the display.)
SURROUND MODE
If you like to adjust sound, go to step 3.
22
3 Adjust the speaker output levels.
I) Press ADJUST repeatedly until one ADJUST
of the following indications (with the _'_
current setting)* appears on the
display.
2)
3)
REAR L :To adjust the left rear speaker output level
(-10 to +10).
* "0" is the initial setting. If you have already changed the
setting, another number (level) will be shown.
Press CONTROL
UP A/ CONTSDL
DOWN UP
DOWN • to adjust the selected I II II
speaker output level. --_>
Repeat steps I) and 2) to adjust
the other speaker levels.
When you select "PL II MUSIC" you can go to the
following adjustment.
4 Turn on Panorama control or off.
I) Press ADJUST repeatedly until
"PANORAMA" (with the current
setting)* appears on the display.
*"OFF" is the initial setting. If you have
already changed the setting, "ON" will be
shown.
ADJUST
2) Press CONTROL UP A/ C0NTSOL
DOWN UP
DOWN • to select if you turn on • "
or off Panorama control, i I_
-%/
• Each time you press the button, "ON"
and "OFF" change alternately.
OFF : Select this when you like to enjoy
originally recorded sounds.
TocancelSurround mode
Press SURROUND ON/OFF again so that "SURROUND OFF"
appears on the display.
• If Surround
mode is canceled while playing back multichannel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer, if you have connected a
subwoofer and set the subwoofer setting correctly--"YES").