Related Manuals for Graco Hydra-Clean 2104E
Summary of Contents for Graco Hydra-Clean 2104E
- Page 1 This manual contains IMPORTANT WARNINGS and INSTRUCTIONS- READ AND RETAIN FOR REFERENCe 2104E.MODEL 800-053 SERIES "A" 2 150 p s i ( 1 50 bar) OPERA TlNG PRESSURE 2250 p s i bar).MAXIMUM WORKING PRESSURE (155...
- Page 2 not use chemicals or agents which are not ~ ~ J J j ~ ~ ~ ~ Q , & ! [ = ; ' b ~ ~ . j ~ ~ ~ compatible with Buna-N and PVC or neoprene cover of hose.
- Page 3 ..-.. TAPE REMOVE FROM PUMP CAP SPRAY !’ \SPRAY HOSE Check Electrical Service and Plug Connect W a t e ~ Supply Before plugging in the sprayer. be sure the electrical service is phase 220 V, 60 HAC. Amp. With the ON-OFF switch in the OFF position, plug the power supplY cord into grounded outlet.
- Page 4 OPERATlQM Startup Before starting, be sure'to read the safety warnings and setup instructions. Check the filter screen in the water inlet connection Turn on the water supply. as often as necessary, a t least daily. not operate the unit with the inlet and filter screen removed. Trigger the gun to release any back pressure.
- Page 5 :he manifold. Nater in pump crankcase. Change oil at month or hour intervals usins May be caused by humid air Graco Crankcase Oil (other approved oil evenl :ondensing into water inside the month or hours) P.N. 801-144. :rankcase. :requent or premature Scored plungers.
- Page 6 CAUSE Check, replace Power cord unplugged, or ectrtc motor w o n t run. building circuit fuse blown Unplug power cord+, decrease pressure. Overload switch has opened. Power.cord unplugged, or Check, replace. building circuit fuse blown, Unplug power cord*, relieve pressure-allow Overload breaker has opened.
- Page 7 Plungers Photo 4. 1 ) U s i n g a n M 1 1 wrench, remove the plunger retainer. Slide out the seal retainer with oil wick and rubber barrier slinger. With a slight twisting motion, loosen the plunger from the plunger rod and remove.
- Page 8 801-392...
-
Page 9: Parts List
51-66 Ref. No. 5 0 Includes items - 5 2 PART DESCRIPTION NO, NO. 801 -023 WASHER, flat, WASHER, 5/16 flat, WASHER, IocIc 1 /4 801.025 WASHER, 5/16 lock, 80.1 -024 NUT, 5/16-18 NC hex, 801 -01 2 GROMMET 801-367 BUMPER -004 PULLEY,... - Page 10 ELECTRICAL SCHEMATIC REF PART DESCRIPTION Items 77-90 are pump internal replacement parts. See exploded view of pump for details. 77 801-027 78 801-028 O-RING, cap 79 801-267 DISCHARGE MANIFOI ..801-038 . RING, backup 89 801-039 O-RING 90 801-040 RETAINER, plunge1 Order parts by name and number.
- Page 11 PARTS DWAVVlMG Gun and Hose Assern REF PART DESCRIPTION NO. NO. 801")7 SPRAY HOSE, 3/8" ID. 50 Repair -083 800-017 SPRAY GUN, parts (replaceable Includes items A, B, C. D, E and F include items 3-1 6) 801-244 HANDLE, left 801-245 HANDLE, right...
-
Page 12: Technical Data
12monthsfromthedateofpurchaseandappliesonlywhentheequipment is installed and operated accordance with written factoryrecommendations.Thiswarrantydoes not cover damage or wear which. in the reasonable judgment of Graco. arises from misuse, abrasion. corrosion, negligence. accident, substitution of non-Graco parts, faulty installation or tampering. This warranty is conditioned...
Need help?
Do you have a question about the Hydra-Clean 2104E and is the answer not in the manual?
Questions and answers