Gas Conversion Kits - Superior SLDVT Series Installation Instructions Manual

GAS CONVERSION KITS

This conversion kit shall be installed by a qualified service agency in accor-
dance with the manufacturer's instructions and all applicable codes and
requirements of the authority having jurisdiction. If the information in these
instruction is not followed exactly, a fire, explosion or production of carbon
monoxide may result causing property damage, personal injury or loss of
life. The qualified service agency is responsible for the proper installation
of this kit. The installation is not proper and complete until the operation
of the converted appliance is checked as specified in the manufacturer's
instructions supplied with the kit.The qualified service agency performing
this installation assumes responsibility for this conversion.
Cette trousse de conversion doit être installée par un technicien agréé,
selon les instructions du fabricant et selon toutes les exigences et tous les
codes pertinents de l'autorité compétente. Assurez-vous de bien suivre
les instructions dans cette notice pour réduire au minimum le risque
d'incendie, d'explosion ou la production de monoxyde de carbone pouvant
causer des dommages matériels, des blessures ou la mort. Le tecnicien
agréé est responsable de l'installation de cette trousse. L'installation n'est
pas adéquate ni complète tant que le bon fonctionnement de l'appareil
converti n'a pas été vérifié selon les instructions du fabricant fournies avec
la trousse. Le fournisseur de service qualifié ayant réalisé l'installation
assume les responsabilités liées à la conversion.
In Canada:
THE CONVERSION SHALL BE CAR-
RIED OUT IN ACCORDANCE WITH THE
REQUIREMENTS OF THE PROVINCIAL
AUTHORITIES HAVING jURISDICTION
AND IN ACCORDANCE WITH THE RE-
QUIREMENTS OF THE CAN/CSA-B149.1
INSTALLATION CODE.
LA CONVERSION DEVRA êTRE EF-
FECTUéE CONFORMéMENT AUX
RECOMMANDATIONS DES AUTORITéS
PROVINCIALES AYANT jURIDICTION
ET CONFORMéMENT AUX EXIGENCES
DU CODE D'INSTALLATION CAN/CSA-
B149.1.
Gas conversion kits are available to adapt your
appliance from the use of one type of gas to
the use of another. These kits contain all the
necessary components needed to complete the
task including labeling that must be affixed to
ensure safe operation.
Kit part numbers are listed here and the follow-
ing steps detail the conversion procedure. Refer
to the instructions provided with the conversion
kit when performing any gas conversion.
38
SUPERIOR DIRECT-VENT GAS FIREPLACES • MODELS SLDVT-30/35/40/45 • INSTALLATION INSTRUCTIONS
WARNING
AVERTISSEMENT
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Millivolt SIT Systems
Natural Gas To Propane Gas
Conversion Kits
Models Catalog No.
SLDVT-30 H6163
SLDVT-35 H7292
SLDVT-40 H6975
SLDVT-45 H7546
Millivolt SIT Systems
Propane Gas to Natural Gas
Conversion Kits
Models Catalog No.
SLDVT-30 H6165
SLDVT-35 H7293
SLDVT-40 H7294
SLDVT-45 85L66
Electronic DEXEN Systems
Natural Gas To Propane Gas
Conversion Kits
Models Catalog No.
SLDVT-30
SLDVT-35
SLDVT-40
SLDVT-45
Electronic DEXEN Systems
Propane Gas To Natural Gas
Conversion Kits
Models Catalog No.
SLDVT-30
SLDVT-35
SLDVT-40
SLDVT-45
INSTALLATION INSTRUCTIONS
Step 1. TURN OFF THE GAS SUPPLY TO THE
APPLIANCE and disconnect power supply at the
circuit breaker. Ensure appliance is cold.
CAUTION: THE GAS SUPPLY SHALL BE
SHUT OFF PRIOR TO DISCONNECTING THE
ELECTRICAL POWER, BEFORE PROCEED-
ING WITH THE CONVERSION.
ATTENTION: AVANT D'EFFECTUER
LA CONVERSION, COUPEZ D'ABORD
L'ALIMENTATION EN GAZ, ENSUITE,
COUPEZ L'ALIMENTATION éLEC-
TRIQUE.
Step 2. Remove the front glass door/frame.
Step 3. Carefully remove the logs. Exercise
care so as not to break the logs.
Step 4. Refer to Figure 56.
Remove the burner assembly with attached
venturi tube.
H6166
H7295
H7973
H7544
H6170
H7296
H7297
H7545