Assembly; Installing Elevation And Tilt Handwheels; Checking Table Insert - Craftsman 113.298051 Owner's Manual

X LookwaEher, 1/4 in. ExternalType
(approx. dia. of hole 1/4 in.) ................ 8
X Lookwasher,5/16 in. External T ype
(approx. dia. of hole 5/16 in.) ............... 4
Z Hex Hd. Screw,5/16-18 x 1-1/2 in. long ........ 2
Z HaxHd. Screw,5/16.18xlin, long ........... 2
BB Truss HeadScrew, 1/4-20 x 5/8 ............... 4
The following parts are included with Model 113.298051
Key
No. PartName 0.ty.
A Leg ..................................... 4
B Side Stiffener .............................. 2
C End Stiffener ............................. ' 2
D Table Extension ........................... 2
Pkg.of Miscellaneous S mall Parts,No. 62767for Legs
Consisting o f the Following:
F Lnckwasher, 1 /4 in. ExternalType
(approx.dia. of hole 1/4 in.) ................ 24
G Hex Nut, 1/4-20
(approx.dia. of hole 1/4 in.) ................ 24
G Hex Nut, 1/2-13
(approx.dia. of hole 1/2 in.) ................ 8
J TrussHeadScrew, 1/4-20 x 5/8 in.long
(top of screwis rounded) .................. 24
K Leveling Foot ............................. 4
Pkg. of Miscellaneous S mall PartsNo. 62745 for
Table ExtenEions,Two Each:
Consistingof the Following'.
E Hex Head Screw5f16-18 x 1-1/4 .............. 8
F LockwaEher,5/1B in. ExternalType
(approx.dia. of hole 5/16 in.) ............... 8
C
F
G
G
H
H
J
L
M
Lockwaeher, 1 /4 in, External Type
(approx.dia. of hole 1/4 in.) ................ 1B
Hex Nut, 5/16-18
(approx.dia. of hole5/16 in.) ............... 8
Hex Nut, 1/4-20
(approx.dia. of hole1/4 in.) ................ 1B
FlatWasher(dia. of hole 11/32) .............. 8
FlatWasher(dia. of hole 17/64) .............. 4
TrussHeadScrew, 1/4-20 x 1in. long
(top of screwis rounded) .................. 1B
CornerStiffener Bracket .................... 4
CornerSupport Bracket ..................... 4
ASSEMBLY
Before mounting the saw on legs,a stand or a bench, the
Table Insert and Blade Squareness and Blade Elevation
must be checked at this time.
INSTALLING ELEVATION AND TILT HANDWHEELS
1. Line up FLAT SPOTS on shaft and handwheel, push
handwheel onto shaft. Install screw and Iockwasher to
lock hendwheel on shaft,
LOCKWASHER
LOCKWASHER
SCREW SCREW
EILT HANDWHEEL EL[VATION HAKIDWHEEL
CHECKING TABLE INSERT
1. With the insert in place, and sawblade all the way down,
use a small scale or straight edge to check near each of
the eight leveling tab positions, in order to determine if
the insert is flush with saw table surface at aPIeight tab
locations.
2. If the insert is above the table surface, the leveling tabs
must be adjusted.
A. Loosen Screw.
B. Lift insert from front end, and pull toward front of
saw.
C. Remove the insert, place it upside down on your
workbench and GENTLY TAP each of the tabs
downward only a slight amount. Replace insert...
check it and readjust tabs, if necessary.
__; LEVELING TAB