Assembly And Adjustments; Assemble Band Saw To Leg Stand; Assemble The Table; Assemble The Sawdust Collection Port - Craftsman 137.224120 Owner's Manual

,SSEMBLY NSTRUCTIONS
Phillips screwdriver Combinationsquare
Adjustable wrench Straight edge
Feeler gauge - size 0.02
or your safety, never connect plug to power source
._ceptacle until all assembly and adjustment steps are
)mpleted, and you have read and understood the safety
nd operating instructions.
EG STAND ASSEMBLY (FIG. A)
Lay the top plate (1) upside down on a flat surface.
Attach a ieg (2) to the outside of the stand top plate
with two carriage bolts (3), washers (4), and nuts (5).
Do not tighten.
Repeat for the remaining three legs.
Attach two long brackets (6) and' two short brackets (7)
to the inside of the legs using carriage bolts (3),
washers (4), and nuts (5). Do not tighten,
Place the leg pad s (8) on each leg and turn the leg
stand' upright on a firm level surface.
Tighten all bolts and nuts with a wrench.
FIG. A
7 I
4
i.
Although compact; this saw is heavy. To avoid back injury,
get help to lift the saw.
ASSEMBLE BAND SAW TO LEG STAND (F_G. B)
t. Lift the saw body (1) and place on the leg stand (2),
aligning with the four mounting holes (3).
2. Attach the band saw to the stand with four long hex
head bolts (4) and four flat washers (5).
3. Place a flat washer (5) and hex nut (6) on each bolt
from the underside. Hand tighten.
4. Tighten all bolts and nuts with a wrench.
FIG. B
I
4
ASSEMBLE THE TABLE
Mounting the trunnion support bracket (F_G. C)
1. Place the trunnion support bracket (1) on the saw body,
as shown,
2. Insert two tong hex head bolts (2, 3) with flat washers (4)
into the threaded holes, through the bracket and saw
body.
3. Open the lower wheel cover (5).
4. Thread a hex bolt (2) Tighten.
5, Close the wheel cover.
6. Thread a nut (7) onto the table stop bolt (8) and screw
both into the rear tab (9) on the trunnion support bracket.
FIG. 0-1
4
3 5
5
ASSEMBLE THE SAWDUST COLLECTION PORT
(FIG. 0-I)
I. Slide thehook (I)on theportassembly into thesquare
hole(2)located on thebandsaw housing,below the
lowerbladeguides.
2. Push the flat plate of the port against the outside of the
band saw to align the holes (3).
3. P_ace a washer (5) on the screw (4), insert and tighten.
NOTE: When operating the band saw, for best sawdust
exhaust attach a dust collection or vacuum hose.
Mounting the table (FIG. D, E)
7. Remove the table insert (10) and table aligning pin (11)
from the table (12).
8. Guide the table slot (13) over the saw blade and rotate
a 1/4 turn, so4he slot is perpendicular to the blade.
FIG. D
12 1 13 10
,
10.
11.
12.
13,
Place the table (12) into the support bracket (1), guiding
the bolts (14)in the scale brackets through the holes in
the trunnion bracket (1).
Align the 0 ° mark on the scale to the pointer (15) on
the trunnion.
Attach the star handle table !ock knobs (16) to the bolts
and tighten. (FIG. E)
Replace the table insert (10), aligning the indents,
Place the table aligning pin (11) in the front of the table,
into the slot (i3), and tighten. (FIG. D)
FIG. E
14
ii_ii;i!i_i_i!ii_!!_!_!_i:;i_i_i'_i:_ _:';:!i:ili_iii:ii:i !_i_i_!ii_!;!i!i!!_i_i_!_;_!_!_i!!i_i!_i_i_;i_!;_i!ii_i:_i!_;_i _i,;:i::!i:i!_:ii_!;i,!_!,!;i;!:i i:i: _i:ii_::::i:ii!_i;_i:i_iiii';i_i:i!:i!i!:_i!_ii!i:!_i:iii_:i!iii: ¸i::i!i:;_i_i_:i :!;!'i;ii,ii!_;,_;:ii:ii::i_::_i_ii::iii_!;:_!_:i:_!!iiii !:i:_ 1 1 _!i_!_;!•_:_:::_!!_;i_:_:_i_:_i_:!!:::_!i!_:_i_!;_;_!_;_i_!i_!_;_!_:_!:_!!:_:_!:_i_;i :_::i_::!_i:i_i!;;_:,_!!i:i;_i!i! _;:_!i_i,!_ii_i;i;_!:;!i::i;!i,!i_!:i!i:i _i!,i:! _! !::_i;:;_!:;_:_:i:!i i_:::i_:!i:ii;iiii_!::i_i::i;ii_'ili,i_il;:::i_;::,!i!i !:_ili:!iii:_il !:!_ii:_:_ ii'i_:i:!;!;_ii;_ii_:i_:!_i
.... : ••: • iL ¸ / _•Li ::•:: ...... • •••• :: •::: •::/ i:_: : ::: •