Parts List - Craftsman 315.218061 Operator's Manual

CRAFTSMAN 10 in. TABLE SAW- MODEL NO. 315.218061
y
The model number will be found on a plate attached to the motor housing. Always mention the model
number in all correspondence regarding your Table Saw or when ordering repair parts.
Key Part
No. Number
1 0134011803
2 0134010211
3 0134010308
4 0134010103-126
5 0101140903
6 410371002
7 0134010212
8 410561014
9 0134011802
10 410561004
11 0134010242
12 0134010219
13 0134010307-129
14 410101005
15 0121011301
16 0134010102-126
17 0134010213
18 0131020220
19 0131010814
20 0131010229
21 410171706
22 0134010911
23 0134010210
24 410171721
25 410011013
26 0134010206
27 411061001
28 0134010332
29 0134010902
30 0134010229
31 410031002
32 0134010306
33 410251017
34 0134010916
35 0134010903
36 410551701
37 0134010209
38 0134010223
39 410351003
PARTS LiST
Key Part
Description Qty.
Rear Rail.................................... 1
End Cap, Rear Rail .................... 2
Rail Holder Nut .......................... 4
Extension Table ......................... 1
Hex Key (M5 x 75 mm) .............. 1
Screw (M6 x 15 mm, Hex Hd.).. 4
End Cap, Right Front Rail ......... 1
Screw (M4 x 5 mm) ................... 1
Front Rail .................................. 1
Screw (M4 x 12 mm, Pan Hd.) .. 3
Stopper, Front Rail .................... 1
Indicator, Extended Table ......... 1
Throat Plate ............................... 1
Screw (M5 x 15 mm, Flat Hd.).. 2
Pad, Throat Plate ...................... 2
Main Table ................................. 1
Slider ......................................... 5
Table Tilt Handle ....................... 1
Screw
(10-24 x 25 mm, Hex Hd.) ......... 4
Carry Handle ............................. 1
Screw (10-24 x 1/2 in.) .............. 8
Miter Table Latch ...................... 1
Guide ........................................ 1
Screw (8-32 x 3/8 in.) ................ 2
Screw (M6 x 40 mm, Hex Hd.).. 1
Locking Block ........................... 2
Lock Nut (M6) ........................... 3
Adjusting Plate .......................... 1
Linkage, Short ........................... 1
Table Extension Lever ............... 1
Carriage Bolt (M6 x 40 mm) ...... 1
Bracket ...................................... 1
Screw w/Washer
(M6 x 12 mm) ............................ 2
Guide Rod ................................. 2
Linkage, Long ........................... 1
Screw w/Washer
(1/4-20 x 1/2 in.)........................ 2
Handle, Left ............................... 1
Holder, Rear Rail ....................... 3
Screw w/Washer
(M6 x 25 mm, Hex Hd.) ............. 6
No. Number
40 0121010214
41 9134015330203
42 0134010237-130
43 410251020
44 0134010322-58
45 410201005
46 0134010314
47 411071707
48 0134011804
49 410192001
50 410109008
51 0134010220
52 0134010315
53 410371003
54 0134010215
55 410031014
56 410341006
57 411171003
58 0134010319
59 0134010321
60 411011707
61 410291006
62 0134015001
63 0134010317
64 0121010901
65 0134010503
66 410109019
67 412011701
68 0101010908
69 0134010305
70 410291004
71 0134010236
72 412011117
73 0134010339
74 410134005
75 0181010246
76 412042002
77 0134010320
78 410499007
79 089110115900
80 0134011301
Description Qty.
Extension Bracket ..................... 2
Warning Label ........................... 1
Cord Wrap ................................. 1
Screw (M6 x 15 mm, Pan Hd.).. 4
Outfeed Support ....................... 1
Screw (M4 x 12 mm, Flat Hd.).. 4
Bar, Sliding Miter Table ............. 2
Lock Nut (1/4-20) ...................... 1
Sliding Bar ................................. 2
Screw (M4 x 10 mm) ................. 2
Screw (M5 x 12 mm, Pan Hd.).. 4
Slider ......................................... 2
Bracket ...................................... 2
Screw w/Washer (M6 x 12 mm) 4
Slider ......................................... 2
Carriage Bolt (M8 x 15 mm) ...... 1
Screw w/Washer (M6 x 12 mm) 2
Wing Nut (M8) ........................... 1
Bracket, Riving Knife ................ 1
Pivot Bracket ............................ 1
Hex Nut (1/4-20) ....................... 1
Screw w/Washer (M8 x 10 mm) 1
Dust Bag ................................... 1
Indicator Bracket ...................... 1
Eccentric Shaft .......................... 1
Plate .......................................... 1
Screw (M6 x 20 mm, Flat Hd.).. 1
Washer (1/4 x 16 x 1T) .............. 2
Nut, Special .............................. 1
Support Bracket ........................ 1
Screw w/Washer
(M6 x 10 mm) ............................ 2
Locking Ring ............................. 1
Washer (M10 x 23 x 2T) ............ 1
Cam .......................................... 2
Screw (M4 x 5 mm, Pan Hd.) .... 2
Adaptor ..................................... 1
Washer (D4)............................... 2
Support Plate, Front Cabinet .... 1
Screw (M5 x 8 mm, Truss Hd.).. 2
Name Plate .............................. 1
Rubber Pad ............................... 1
42