Accessories Bag - Mountfield 4135H Instructions For Use Manual

EN
Clean the entire machine. It is particularly
important to clean under the cutting deck. Touch
up paint damage to prevent rust.
Store the machine indoors in a dry place.
Machines with an electric starter:
Remove the battery. Store it well charged in a cool
place (between 0°C and +15°C).
At the correct storage temperature, the battery
should be maintenance-charged every four
months.
The battery acid is extremely corrosive
and can cause injuries and damage to
skin and clothing. Always use rubber
gloves and glasses (goggles) to protect
your eyes. Avoid inhaling any acid
vapour.
Do not incline the battery too much so
that the battery acid can run out onto
hands or clothing. If this should
happen, rinse with plenty of water.
4 ASSEMBLY
To avoid injury and damage to people
and property, do not use the machine
until all the measures in this instruction
have been carried out..

4.1 Accessories bag

The machine is supplied with a plastic bag contain-
ing components which shall be used during the as-
sembly. The bag contains (fig. 1):
Pos. No. Designation
B Spare key
C 1 Tension pin
D 1 Shim washer
E 1 Shim washer
F 2 Shoulder washer
G 2 Screw
H 2 Screw knob
I 4 Washer
J 1 Drawing plate
K 4 Screw
L 2 Nut
M 2 Screw for battery
N 2 Nut for battery
O 2 Screw
P 2 Nut
Supplied installed on the front axles:
Pos No. Designation
Q 2 Lock pin
R 2 Washer
Secure to the implement lifter:
Pos No. Designation
S 2 Deck mount
10
ENGLISH
4.2 Engine casing
To fill with fuel and to inspect and maintain the en-
gine and battery, open the engine casing.
1. Raise the seat lock (fig. 2) and fold the seat for-
wards.
2. Pull up the rubber strap at the front edge of the
casing (fig. 3).
3. Grasp the front edge of the engine casing and
fold up the casing (fig. 4).
4.2.2 Closing
1. Grasp the front edge of the engine casing and
fold down the casing (fig. 4).
2. Secure the front edge of the casing with the rub-
ber strap (fig. 3).
4.3 Battery
See "8.8 Battery".
4.4 Seat, fig. 6
Release the catch (S) and fold up the seat bracket.
Install the mounting in the rear (upper) holes as
follows:
Dimension
1. Install the shoulder washers (F) on the screws
(K).
6 x 36
2. Insert the screws through the slots in the brack-
16 x 38 x 0.5
et. Place a washer (I) between the seat and the
16 x 38 x 1.0
bracket.
3. Tighten the screws in the seat. Tightening
8 x 20
torque: 9±1.7 Nm.
8.4 x 24 x 1.5
8 x 20
4. Check that the seat moves easily in the slots in
the bracket.
Install the mounting in the front (lower) holes as
follows:
1. Install the screw knobs (H) on the screws (G).
M10 x 35
2. Install a washer (I) on each screw.
M10
3. Insert the screws through the slots in the bracket
and tighten by hand in the seat.
4. Fold the seat down and place it in the desired
position.
5. Tighten the screw knobs (H) by hand.
The engine must not be running when
the casing is opened.
4.2.1Opening
The machine may not be operated un-
less the engine casing is closed and
locked. Risk of burns and crushing in-
juries.
If the screws are tightened more than
9±1.7 Nm, the seat will be damaged.
The screw knobs (H) and the seat will
be damaged if tools are used.