Variable Speed - Craftsman Nextec 320.17562 Operator's Manual

A
ABt,WARNING: The safe use of this product requires an understanding of the
information on the tool and in this operator's manual, as well as knowledge of
the project you are attempting. Before use of this product, familiarize yourself
with all operating features and safety rules.
VARIABLE SPEED
The variable-speed trigger switch delivers higher speed with increased pressure
and lower speed with decreased trigger pressure. [,] d d-'T-,_ d[,] _1
FORWARD/CENTER LOCK/REVERSE
The direction-of-rotation selector located above the trigger switch changes
the direction of bit rotation. Setting the trigger switch in the OFF (center lock)
position helps to reduce the possibility of accidental starting.
LED WORK LIGHT
Pressing the trigger switch illuminates the LED worklight. This feature provides
extra light for increased visibility.
FuelGauge
Indicates the battery-pack charge level.
• r_,."_"] d _ I:] a5"4
A WARNING: If any part is broken or missing, do not attempt to plug in the
power cord, attach the battery pack or operate the 12V Right-Angle Impact
Driver until the broken or missing part is replaced. Failure to do so could result
in possibly serious injury.
a WARNING: Do not attempt to modify this 12V Right-Angle Impact Driver or
create accessories not recommended for use with this tool. Any such alteration
or modification is misuse and could result in a hazardous condition leading to
possible serious injury.
A WARNING: To prevent accidental starting that could cause serious personal
injury, always remove the battery pack from the Right-Angle Impact Driver when
assembling parts.
UNPACKING
This product has been shipped completely assembled.
• Carefully remove the tool and any accessories from the box. Make sure that
all items listed in the packing list are included.
• Inspect the tool carefully to make sure that no breakage or damage occurred
during shipping.
• Do not discard the packing material until you have carefully inspected and
satisfactorily operated the tool.
• If any parts are damaged or missing, please refer to the numbers listed on
the back page of operator's manual.
PACKING LIST
Right-Angle Impact Driver, soft case, 1-3/8" Phillips screwdriver bit, 1A" nut
driver bit, 3/8" nut driver bit, 5/16" nut driver bit, operator's manual.
LOW-BATTERY CAPACITY INDICATOR
NOTE: The new battery pack is not fully charged!
First, read the safety rules, and then follow the instructions in the sections
entitled "Important charging notes" and "Charging the battery".
Important charging notes
1. Longest life and best performance can be obtained if batteries are charged
at normal room temperature.
2. While charging a battery, the charger will normally become warm.
3. If the batteries do not charge properly:
A. Verify the current at the outlet by plugging in a lamp or other appliance
and turning it on.
B. Determine whether the outlet is connected to a light switch that turns the
power off when you turn out the lights; if so, make sure that the power is
turned on.
4.
5,
The battery pack should be recharged when it fails to produce sufficient
power on jobs that were previously done easily or when the FuelGauge
shines red to indicate that the charge is depleted. Do not continue to use
the tool under these conditions. Repeat the charging procedure.
Unplug the charger from the power supply before disconnecting it from the
tool. Unplug the charger before attempting to clean.
6. Battery life depends on usage, storage temperature and time.
7. The charger is intended to be used in a vertical or floor-mounted position.
Unlike other battery types, Lithium-Ion battery delivers fade-free power for their
entire run time. The tool will not experience a slow, gradual loss of power as
you work. To signal that the battery is at the end of its run time and needs to be
charged, the power to the tool will drop quickly.
NOTE: The LED worklight may flash slowly and the FuelGauge may not
illuminate in the case of an overload or high temperature (see BA-I-i-ERY
PROTECTION, Page 12).
17562 Manual_Revised_SO 0607 Page 10 17562 ManuaLRevised_lO 0607 Page 11