Summary of Contents for Craftsman 11483 - C3 19.2 Volt Impact Driver
SOLD SEPARATELY operator's manual before using this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA Visit the Craftsman web page: www.sears.com/craftsman 983000-987 Save this manual for future reference 04-24-08 (REV:02)
SEARS STORE OR OTHER CRAFTSMAN OUTLET iN THE UNITED STATES FOR FREE REPLACEMENT. If this Craftsman tool is used for commercial or rental purposes, this warranty applies for only 90 days from the date of purchase. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
not use a power tool while you are tired or under WARNING! Read all instructions. Failure to the influence of drugs, alcohol or medication. follow all instructions listed below may result in moment of inattention while operating power tools may electric shock, fire and/or serious injury.
 Keepcuttingtoolssharpandclean.Properly main- nails, screws, or other small metal objects that can make a connection from one terminal to another. tainedcuttingtoolswithsharpcuttingedges areless likely to bindandareeasier t o control. Shorting the battery terminals together may cause burns or a fire. Use the power tool, accessories and tooJ bits etc., in accordance with these instructions and in the...
Someofthe following symbols maybeusedonthisproduct. P lease studythemandlearn theirmeaning. Proper i nter- pretation ofthesesymbols willallowyouto operate the productbetter andsafer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Current Amperes Hertz Frequency (cycles per second) Watt Power Minutes Time Alternating Current Type of current Direct Current Type or a characteristic of current No Load Speed...
If you do not understand the warnings and to your nearest SEARS PARTS AND REPAIR SERVICE instructions in the operator's manual, do not use this CENTER for repair. When servicing, use only identical product. Call the Craftsman Consumer Helpline at replacement parts. 1-800-932-3188 for assistance. WARNING: The operation of any power tool can result in foreign objects being thrown into your eyes, which can result in severe eye damage.
PRODUCT SPECiFICATiONS No Load Speed ........0-2,400 r/min. (RPM) Coupler ............1/4 in. Keyless Motor ............... 19.2 Volt DC Blows Per Minute .......... 0-3,500 BPM* Torque ..............900 in.lb. Switch ......VSR (Variable Speed Reversible) *Blows per minute BUILT-IN COUPLER WORKLIGNT DIRECTIONOF SWITCH...
KNOWYOURIMPACTDRIVER LED WORKLIGHT See Figure 1. The LED worklight, located below the coupler, illuminates The safe use of this product requires an understanding when the switch trigger is depressed. This provides extra the information on the tool and in this operator's manual light for increased visibility.
 Driving Tapcon screws into block walls and concrete  Driving screws into metal studs  Driving nuts and bolts using an impact socket This product will accept DieHardo 19.2 V lithium-ion bat- tery packs and Craftsman 19.2 V nickel-cadmium battery DEPRESS LATCHES packs.
To stop the impact driver, release the switch trigger and WARNING: Battery tools are always in operating allow the coupler to come to a complete stop. condition. Therefore, the switch should always be locked when not in use or carrying at your side. NOTE: The impact driver will not run unless the direction of rotation selector is pushed fully to the left or right.
BIT STORAGE INSTALLING THE MAGNETIC BIT HOLDER See Figure 6. DRILL BIT OR SOCKET ADAPTOR See Figure 8. When not in use, bits provided with the tool can be placed in the storage area located at the bottom of the tool handle.  Lock the switch trigger by placing the direction of rotation selector in the center position.
DRIVINGOR REMOVINGSCREWS See Figures 9 - 10.  Place the direction of rotation selector in the correct position for the operation.  Hold the impact driver with one hand.  Place the bit on the screw head and slowly depress the switch trigger.
AND PREPARATION BATTERIES FOR RECYCLING This product will accept DieHardo 19.2 V lithium-ion bat- To preserve natural resources, please tery packs and Craftsman 19.2 V nickel-cadmium battery recycle or dispose of batteries packs. properly. The batteries for this product have been designed This product uses nickel-cadmium to provide maximum trouble-free life.
CRAFTSMAN 19.2 VOLT IMPACT DRIVER - MODEL NUMBER 315.114831 The model number will be found on a plate attached to the motor housing, Always mention the model number in all correspondence regarding your IMPACT DRIVER or when ordering repair parts,...