Table of Contents
Advertisement
Enhanced Mode Support On [S-ATA]
The default setting SATA allows you to use native OS on Serial ATA
and Parallel ATA ports. We recommend that you do not change the
default setting for better OS compatibility. In this setting, you may
use legacy OS on the Parallel ATA ports o n l y i f
Serial ATA device.
The S-ATA+P-ATA and P-ATA options are for advanced users only. If
you set to any of these options and encounter problems, revert to the
default setting S A T A
[S-ATA] [P-ATA]
The O n b o a r d I D E O p e r a t e M o d e
when the C o n f i g u r e S A T A A s
Onboard Serial-ATA BOOTROOM [Disabled]
Enables or disables the onboard Serial ATA boot ROM.
Configuration options: [Disabled] [Enabled]
The O n b o a r d S e r i a l - A T A B O O T R O M
C o n f i g u r e S A T A A s item is set to RAID.
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
ALPE and ASP [Disabled]
Enables or disables the ALPE and ASP.
Configuration options: [Disabled] [Enabled]
S t a g g e r S p i n u p S u p p o r t [ D i s a b l e d ]
S t a g g e r S p i n u p S u p p o r t [ D i s a b l e d ]
S t a g g e r S p i n u p S u p p o r t [ D i s a b l e d ]
S t a g g e r S p i n u p S u p p o r t [ D i s a b l e d ]
S t a g g e r S p i n u p S u p p o r t [ D i s a b l e d ]
Enables or disables the stagger spinup support.
Configuration options: [Disabled] [Enabled]
A H C I P o r t 3 I n t e r l o c k S w i t c h [ D i s a b l e d ]
A H C I P o r t 3 I n t e r l o c k S w i t c h [ D i s a b l e d ]
A H C I P o r t 3 I n t e r l o c k S w i t c h [ D i s a b l e d ]
A H C I P o r t 3 I n t e r l o c k S w i t c h [ D i s a b l e d ]
A H C I P o r t 3 I n t e r l o c k S w i t c h [ D i s a b l e d ]
Enables or disables the Advanced Host Controller Interface (AHCI)
Port 3 interlock switch. Configuration options: [Disabled] [Enabled]
The A L P E a n d A S P
A s
A s
A s
A s item is set to AHCI.
A s
IDE Detect Time Out [35]
IDE Detect Time Out [35]
IDE Detect Time Out [35]
IDE Detect Time Out [35]
IDE Detect Time Out [35]
Selects the time out value for detecting ATA/ATAPI devices.
Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]
5 - 1 8
5 - 1 8
5 - 1 8
5 - 1 8
5 - 1 8
S A T A. Configuration options: [S-ATA+P-ATA]
S A T A
S A T A
S A T A
O n b o a r d I D E O p e r a t e M o d e
O n b o a r d I D E O p e r a t e M o d e
O n b o a r d I D E O p e r a t e M o d e and its submenu items appear only
O n b o a r d I D E O p e r a t e M o d e
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s item is set to Standard IDE.
C o n f i g u r e S A T A A s
O n b o a r d S e r i a l - A T A B O O T R O M
O n b o a r d S e r i a l - A T A B O O T R O M
O n b o a r d S e r i a l - A T A B O O T R O M item appears only when the
O n b o a r d S e r i a l - A T A B O O T R O M
A L P E a n d A S P
A L P E a n d A S P item appears only when the C o n f i g u r e S A T A
A L P E a n d A S P
A L P E a n d A S P
o n l y i f
o n l y i f you did not install any
o n l y i f
o n l y i f
C h a p t e r 5 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 5 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 5 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 5 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 5 : M o t h e r b o a r d i n f o r m a t i o n
C o n f i g u r e S A T A
C o n f i g u r e S A T A
C o n f i g u r e S A T A
C o n f i g u r e S A T A
Advertisement
Table of Contents
