Table of Contents
Advertisement
Quick Links
Introducing the USB 2.0+1394 DV Kit
The USB 2.0+1394 DV Kit is a complete DV editing kit --
a combo card with USB 2.0 and FireWire (1394a) interfaces,
deluxe DV editing software (full DV, AVI, QuickTime,
Windows Media, RealNetworks, and MPEG2 support)
and a 1394 6-pin/4-pin DV cable.
Features and Benefits
•
Combo card design adds four USB 2.0 (480 Mbps)
and three 1394a (400 Mbps) ports into your system.
•
Hot-swapping feature allows you to connect/
disconnect devices without first turning your system
off
USB 2.0 interface
•
Adds three external and one internal USB 2.0 ports
•
Compliant with USB specification rev. 2.0
•
Supports high-speed (480 Mbps), full-speed (12
Mbps), and low-speed (1.5 Mbps) data transfer
modes for simultaneous operation of multiple USB
2.0/1.1 devices
Note: USB 1.1 devices are limited to USB 1.1 speeds
even when they are connected to USB 2.0 host adapter
or USB 2.0 hubs.
FireWire (1394a) interface
•
Adds two external and one internal FireWire ports
04-0288E
USB 2.0+1394 DV Kit
Quick Installation Guide
1
Advertisement
Table of Contents
Related Manuals for SIIG USB 2.0+1394 DV Kit
Summary of Contents for SIIG USB 2.0+1394 DV Kit
-
Page 1: Quick Installation Guide
USB 2.0+1394 DV Kit Quick Installation Guide Introducing the USB 2.0+1394 DV Kit The USB 2.0+1394 DV Kit is a complete DV editing kit -- a combo card with USB 2.0 and FireWire (1394a) interfaces, deluxe DV editing software (full DV, AVI, QuickTime, Windows Media, RealNetworks, and MPEG2 support) and a 1394 6-pin/4-pin DV cable. - Page 2 • IEEE 1394-1995, P1394a (rev. 1.1) and OHCI Interface Specification 1.0 compliant • Supports serial bus data transfer rates of 100, 200 and 400 Mbps System Requirements • Pentium or equivalent computer with an available PCI slot • Windows 98SE/ME •...
-
Page 3: Board Layout
Board Layout 1394 Port 1394 Ports USB 2.0 Port Power Connector (optional) USB 2.0 Ports Figure 1. Board Layout Note: This power connector (same as the one used with your floppy disk drive) is designed to provide additional power to the board when needed. -
Page 4: Hardware Installation
Hardware Installation General instructions for installing the card are provided below. Since the design of computer cases and motherboards vary, refer to your computer’s reference manual for further information, if needed. Static Electricity Discharge may permanently damage your system. Discharge any static electricity build up in your body by touching your computer’s case for a few seconds. - Page 5 Click Start, then Run. Type in X:\setup.exe and click OK. (Change X: to match your CD-ROM drive letter) Click Next, Next, at the Warning box click OK, then click Finish to restart. When the VIA ...Universal Host Controller is detected, click Next. Choose Search for the best driver...
- Page 6 Click Start, then Run. Type X:\setup.exe and click OK. (Change X: to match your CD-ROM drive letter). Follow the on-screen instructions to install the driver. When prompted click Finish to restart. At the Add New Hardware Wizard, choose Automatic search for a better ..., click Next, then click Finish.
- Page 7 When Windows restarts, the drivers will install automatically. Windows XP/Server 2003 Windows XP Service Pack 1 (SP 1) or later is required for this installation. Windows XP Service Pack 1 or later will automatically detect and install the correct drivers for this board. Windows 2003 Server will automatically detect and install the correct drivers for this board.
- Page 8 b) Under the 1394 Bus Controller or IEEE 1394 Bus host controllers: - VIA OHCI Compliant IEEE 1394 Host Controller Windows 2000 (with SP4 or later): a) Under the Universal Serial Bus Controllers: - VIA ... Universal Host Controller - VIA ... Universal Host Controller - VIA USB Enhanced Host Controller - USB 2.0 Root Hub - USB Root Hub...
- Page 9 Ulead VideoStudio Software Installation The USB 2.0 + 1394 DV Kit includes Ulead VideoStudio ® digital video editing software for producing home videos complete with attractive titles, transitions and sounds. Before installing VideoStudio, make sure your adapter and DV camcorder are properly installed and configured. See next section, Connecting DV Camcorder, for more details on how to properly install your DV camcorder.
- Page 10 To Verify Successful DV Camcorder Setup Check Device Manager to verify successful driver installation. Windows 98SE/ME: From the main desktop, right click My Computer, then click Properties. Click Device Manager tab. Windows 2000/XP/2003: Right click My Computer, click Manage, then click Device Manager. Double click Imaging Device(s).
-
Page 11: Technical Support And Warranty
This product comes with a lifetime manufacturer warranty. Please see SIIG website for more warranty details. If you should happen to have any problems with this product, follow the procedures below. A) If it is within the store's return policy period, please return the product to the store where you purchased from. - Page 12 Fremont, CA 94538-3152 USB 2.0+FireWire DV Kit is a trademark of SIIG, Inc. SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel Corporation. Other names used in publication are for identification only and may be trademarks of their respective companies.